海宝2603-操作时序方案.ppt

* Ramp-down Sequence Off-valve is de-engerziged Gases switch from Pre-Flow to Cut-Flow Motion signal de-activated Chopper current is ramped down exponentially Choppers are disabled Main contactor de-activated and off-valve is re-activated * Ramp-down Sequence Off-valve is de-engerziged Gases switch from Pre-Flow to Cut-Flow Motion signal de-activated Chopper current is ramped down exponentially Choppers are disabled Main contactor de-activated and off-valve is re-activated * Ramp-down Sequence Off-valve is de-engerziged Gases switch from Pre-Flow to Cut-Flow Motion signal de-activated Chopper current is ramped down exponentially Choppers are disabled Main contactor de-activated and off-valve is re-activated * Ramp-down Sequence Off-valve is de-engerziged Gases switch from Pre-Flow to Cut-Flow Motion signal de-activated Chopper current is ramped down exponentially Choppers are disabled Main contactor de-activated and off-valve is re-activated Copyright, 2007 Hypertherm, Inc. These materials cannot be reproduced in any formwithout the permission of Hypertherm, Inc. * 操作时序 HPR130 System Overview Rev. 0 Copyright, 2004 Hypertherm, Inc. These materials cannot be reproduced in any formwithout the permission of Hypertherm, Inc. HyPerformance? Plasma 操作时序 等离子电源状态: 0: 上电 2: 吹扫 3: 等待 4: 预流 5: 弧建立 6: 弧转移 7: 渐升 8: 稳定状态 9: 渐降 10: 自动关闭 和其他 状态 0 – 等待 1 动作 OK 不OK, 请检查 1 等离子没有准备好接受启动信号 PCB 3 LEDN300 第4灯条亮 如果PCB3 LEDN300 第10灯条亮? (起动信号被输入) 2 同气体控制器建立通讯 进入下一状态 Error 133? 3 互锁检测 开机时不能有起动信号 Error 50? 4 开机时不能有冷却液流量 Error 109? 5 开机时斩波器不能有输出 Error 102? 6 没有弧转移信号 Error 108? 7 开机时不能有过热信号. Error 99,100,101,111? 状态0 – 等待 1 PCB3 状态 2 – 吹扫 动作 OK 不OK, 请检查 1 冷却液流量检查 水泵起动, 12秒后流量开关检测, 至少 0.6GPM. Error 93? 是否有冷却液? 叶轮转吗? D26 (P/S PCB2) 亮吗? 有120VAC 在流量开关上的J1pins 1 & 3吗? P/S PCB3 TP206 & 210之间的电压是 (.8VDC) P/S PCB2 J13 Pins 1and 2有24VDC吗? 240 VAC 到水泵电机吗? 参考手册中的流量测试. 2 气体管路吹扫 (air or N2) 气体流过割枪20秒 Error 139? 气体供上了吗? 气体管路受阻了吗? 3 斩波器电流输出检测 可以听到主接触器吸合. 进入下一状态 主接触器吸合了吗? P/S P