logo

您所在位置网站首页 > 海量文档  > 行业资料 > 国内外标准规范

A0213_A0213M-06a无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管.docx 14页

本文档一共被下载: ,您可全文免费在线阅读后下载本文档。

  • 支付并下载
  • 收藏该文档
  • 百度一下本文档
  • 修改文档简介
全屏预览

下载提示

1.本站不保证该用户上传的文档完整性,不预览、不比对内容而直接下载产生的反悔问题本站不予受理。
2.该文档所得收入(下载+内容+预览三)归上传者、原创者。
3.登录后可充值,立即自动返金币,充值渠道很便利
特别说明: 下载前务必先预览,自己验证一下是不是你要下载的文档。
  • 内容提供方 bigone123(上传创作收益人)
  • 发布时间:2016-11-24
  • 需要金币300(10金币=人民币1元)
  • 浏览人气
  • 下载次数
  • 收藏次数
  • 文件大小:108.65 KB
下载过该文档的会员
A0213_A0213M-06a无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管
你可能关注的文档:
Used in USDOE-NE standardsDesignation: A 213/A 213M – 06aStandard Specification forSeamless Ferritic and Austenitic Alloy-Steel Boiler,Superheater, and Heat-Exchanger Tubes1This standard is issued under the fixed designation A 213/A 213M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.Scope*This specification2 covers seamless ferritic and austen-itic steel boiler, superheater, and heat-exchanger tubes, desig-nated Grades T5, TP304, etc. These steels are listed in Tablesand 2.Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements.The tubing sizes and thicknesses usually furnished to this specification are 1?8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification.The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specifi-cation. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.Reference

发表评论

请自觉遵守互联网相关的政策法规,严禁发布色情、暴力、反动的言论。
用户名: 验证码: 点击我更换图片

“原创力文档”前称为“文档投稿赚钱网”,本站为“文档C2C交易模式”,即用户上传的文档直接卖给(下载)用户,本站只是中间服务平台,本站所有文档下载所得的收益归上传人(含作者)所有【成交的100%(原创)】。原创力文档是网络服务平台方,若您的权利被侵害,侵权客服QQ:3005833200 电话:19940600175 欢迎举报,上传者QQ群:784321556