船用防锈漆生产工艺流程图200871145624e3ykc5n0B7C..docVIP

1.1 船用防锈漆生产工艺流程图flow chart for the manufacturing process of anticorrosive marine paint 树脂resin, 防锈颜料antirust paint, 调速分散机speed regulation disperser, 混合均匀mixed well, 砂磨机sand mill, 研磨triturate, 测细度 measure the fineness of grind , 调速分散机speed regulation disperser, 助剂additives, 溶剂impregnant , 分散disperse , 调黏，测黏度attemper and test the viscosity, 防结皮剂anti-skinning agent, 分散disperse, 取样sampling, 质量检测quality testing, 检测合格qualified, 过滤包装filtrate and pack 1.2 试验方法1.2.1 取样产品取样按 GB/T 3186-82《涂料产品的取样》进行，样品分为两份，一份作为检测样品，一份作为备用样品。 SSampling Paint Products ,and divides into two,one for testing, the other for spare use1.2.2 黏度iscosity按GB/T 1723-93 〈〈涂料黏度测定法〉〉进行，采用乙法：涂-4黏度法进行。Tviscosity (Mr -4)1.2.3 细度ineness按GB/T 1724-79〈〈涂料细度测定法〉〉进行Methods of Test for Fineness of Grind of Paints1.2.4 附着力dhesion按GB/T 1720-79〈〈涂膜附着力测定法〉〉进行Determination of Adhesion of Film1.2.5 固体含量olid content按GB/T 1725-79 〈〈涂料固体含量测定法〉〉进行Methods of Test For Non-volatile Matter of Varnishes, Paints And Their Vehicles1.2.6 干燥时间rying time按GB/T 1728-79〈〈漆膜、腻子干燥时间测定法〉〉进行，其中表面干燥时间采用乙法：指触法进行，实际干燥时间采用丙法：刀片法。Methods of Test For Drying Time of Coatings of Paints And Putties, adopt the second way to test the drying time of the surface by touching it. And the actual drying time please adopt the third way by using knives1.2.7 漆膜颜色及外观按GB/T1729-79〈〈漆膜颜色及外观测定法〉〉进行Determination of Color and Appearance of Films.1.2.8 柔韧性按GB/T 1731-93〈〈漆膜柔韧性测定法〉〉进行Determination of Flexibility of Films1.2.9 耐冲击性按GB/T 1732-93〈〈漆膜耐冲击性测定法〉〉进行Determination of Impact Resistance of Films1.2.10硬度按GB/T6732-96〈〈漆膜硬度铅笔测定法〉〉进行Determination of Film Hardness by Pencil Test1.2.11耐盐水性resistance to salt water按GB/T1763-79〈〈漆膜耐化学试剂性测定法〉〉进行Method of Test For Chemical Resistance of Paint Films1.2.12对面漆的适应性daptability to finish选用相应配套的各色合成树脂漆，用于测定面漆的适应性。按GB/T 1727-79〈〈漆膜一般制备法〉〉进行涂刷。先涂刷一道船用防锈漆，按产品技术要求干燥后，涂刷一道面漆，在涂刷时观察涂刷性。待面漆干燥24小时后，观察漆膜表面有无缩孔、裂纹、针眼、起泡、剥落等现象hoose the matched resin paint of all kinds to test the adaptability to finish. Painting accordi