matlab参考.docVIP

a=linspace(0,2*pi,50); x=5*cos(a); y=5*sin(a); [X,Y]=meshgrid(x,y); Z=sin(sqrt(X.^2+Y.^2))./sqrt(X.^2+Y.^2); %%%不知道这个曲面画的对不对，你看一下 surf(X,Y,Z) hold on [U V W]=surfnorm(X,Y,Z); quiver3(X,Y,Z,U,V,W,0.4) 2.知道了一些点(x,y,z)坐标,怎样用MATLAB绘制出三维曲面? 知道一系列点的坐标如下（1.486,3.059,0.1）;（2.121,4.041,0.1）;（2.570,3.959,0.1）;（3.439,4.396,0.1）;（4.505,3.012,0.1）;（3.402,1.604,0.1）;（2.570,2.065,0.1）;（2.150,1.970,0.1）;（1.794,3.059,0.2）;（2.121,3.615,0.2）;（2.570,3.473,0.2）;（3.421,4.160,0.2）;（4.271,3.036,0.2）;（3.411,1.876,0.2）;（2.561,2.562,0.2）;（2.179,2.420,0.2）;（2.757,3.024,0.3）;（3.439,3.970,0.3）;（4.084,3.036,0.3）;（3.402,2.077,0.3）;（2.879,3.036,0.4）;（3.421,3.793,0.4）;（3.953,3.036,0.4）;（3.402,2.219,0.4）;（3.000,3.047,0.5）;（3.430,3.639,0.5）;（3.822,3.012,0.5）;（3.411,2.385,0.5）;（3.103,3.012,0.6）;（3.430,3.462,0.6）;（3.710,3.036,0.6）;（3.402,2.562,0.6）;（3.224,3.047,0.7）;（3.411,3.260,0.7）;（3.542,3.024,0.7）;（3.393,2.763,0.7）怎样用MATLAB绘制成三维曲面呢？ A=[1.486,3.059,0.1;2.121,4.041,0.1;2.570,3.959,0.1;3.439,4.396,0.1;4.505,3.012,0.1;3.402,1.604,0.1;2.570,2.065,0.1;2.150,1.970,0.1;1.794,3.059,0.2;2.121,3.615,0.2;2.570,3.473,0.2;3.421,4.160,0.2;4.271,3.036,0.2;3.411,1.876,0.2;2.561,2.562,0.2;2.179,2.420,0.2;2.757,3.024,0.3;3.439,3.970,0.3;4.084,3.036,0.3;3.402,2.077,0.3;2.879,3.036,0.4;3.421,3.793,0.4;3.953,3.036,0.4;3.402,2.219,0.4;3.000,3.047,0.5;3.430,3.639,0.5;3.822,3.012,0.5;3.411,2.385,0.5;3.103,3.012,0.6;3.430,3.462,0.6;3.710,3.036,0.6;3.402,2.562,0.6;3.224,3.047,0.7;3.411,3.260,0.7;3.542,3.024,0.7;3.393,2.763,0.7]; x=A(:,1); y=A(:,2); z=A(:,3); scatter(x,y,5,z) %散点图figure[X,Y,Z]=griddata(x,y,z,linspace(1.486,4.271),linspace(1.604,4.276),v4); %插值pcolor(X,Y,Z); shading interp %伪彩色图 figure, contourf(X,Y,Z) %等高线图 figure, surf(X,Y,Z)%三维曲面 看这些点是不是很规矩的网格点的数据。如果是网格点数据，适当做点重组，就可以用surf函数得到曲面图。如果不是网格点数据，那么请用griddata函数插值到网格点数据，然后再surf如：data=[1 1 5.141 2 9.561 3 8.662 1 12.552 2 10.512 3 2.73 1 22.033 2 22.973 3 32.944 2 55.584 3 24.55]; %第一列为x,第二列为y，第三列为z[xx,yy]=mesh