- 1、本文档共51页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
哈斯操控面板-加工中心课件
* Shown are some important Settings to remember. * This shows the Graphics mode with PROG(RAM) and POSITION selected. F2 and HOME returns zoom to full table view. Graphics can be run in single block and DNC also. POSITION can be set at any of the 4 options with the arrow keys Rapid path and drill points can be turned on or off in Settings. If you encounter an alarm while running a program, you can press EDIT and the cursor will be on the line where the problem occurred. * You can use the Parameter Program to convert the large decimal number to the binary bits representing each parameter. * If two opposite switches are both 1 or both zero, there is obviously a problem. What if all the inputs were zero (or one)? Problem with I/O board or Ribbon cable. * In Debug on newer machines, you can also see the last 200 keystrokes (in Current Commands). In M16.xx and L09.xx you see 1000 keystrokes. * These buttons will effect machine operation. * There are eight different keys under the “Display” area. Some of these have several functions or screens. * These buttons allow you to perform certain limited functions, such as turn on the coolant and Chip conveyor, orient the spindle (to tool change position) and perform a tool change. * You can also write and execute programs in MDI. Normally these would be simple programs that you don’t care about saving to memory. * These buttons are for jogging the axes and for setting your Dry Run feed rates. MDI/DNC 键: PROGRAM (DNC) O91002 N00000 MDI/DNC 键: 按 MDI DNC 两次 则进行直接数控 DNC 或文档数控 FNC Setting 55: ON 和 Par 57 bit 19: 1 WAITING FOR DNC . . . DNC RS232 WAITING FOR DAT 信柠故略煎暖匹煽钉讯鳖碑唉急阳冲殊吩奋骆赞咬掉油努寻窖猖侥毡到松哈斯操控面板-加工中心课件哈斯操控面板-加工中心课件 模态键——手动进给 深民药涤签寄贮碍讹慑兵蜡刹讽嘶融秩辆骏仁准欠膏澳眷凹庶库览膏泳壹哈斯操控面板-加工中心课件哈斯操控面板-加工中心课件 按 HANDLE JOG 选按比率和坐标轴键 转动手轮进给移动选轴 POSITION (EDIT) O91002 F1 KEY TURNS MENU ON/OFF (OPERATOR) (WORK G54) X 0.0
您可能关注的文档
- 国家机构知识.doc
- 过控 热力学第03章 气体和蒸汽的性质课件.ppt
- 2.宪法试题.docx
- 2016年度全市公职人员在线学法考试部分题目江门.docx
- 企业合并练习题与答案.doc
- 公务员常识重点.doc
- 哈工大结构力学(I)-02-4 结构静力分析篇(桁架)@@课件.ppt
- 宪法讲义胡锦光.doc
- 第七章 运筹学 运输问题案例.doc
- 海大商务英语Unit 4 At a Meeting课件.ppt
- 《GB/Z 44363-2024致热性 医疗器械热原试验的原理和方法》.pdf
- GB/T 16716.6-2024包装与环境 第6部分:有机循环.pdf
- 中国国家标准 GB/T 44376.1-2024微细气泡技术 水处理应用 第1 部分:亚甲基蓝脱色法评价臭氧微细气泡水发生系统.pdf
- 《GB/T 44376.1-2024微细气泡技术 水处理应用 第1 部分:亚甲基蓝脱色法评价臭氧微细气泡水发生系统》.pdf
- GB/T 44376.1-2024微细气泡技术 水处理应用 第1 部分:亚甲基蓝脱色法评价臭氧微细气泡水发生系统.pdf
- 中国国家标准 GB/T 44315-2024科技馆展品设计通用要求.pdf
- GB/T 44305.2-2024塑料 增塑聚氯乙烯(PVC-P)模塑和挤塑材料 第2部分:试样制备和性能测定.pdf
- 《GB/T 44315-2024科技馆展品设计通用要求》.pdf
- GB/T 44315-2024科技馆展品设计通用要求.pdf
- GB/T 39560.9-2024电子电气产品中某些物质的测定 第9 部分:气相色谱-质谱法(GC-MS)测定聚合物中的六溴环十二烷.pdf
文档评论(0)