冷旋压封头工艺守则（Code of practice for cold spinning heads）.docVIP

下载本文档

8
0
约1.17万字
约 16页
2017-07-24 发布于河南
举报
版权申诉

冷旋压封头工艺守则（Code of practice for cold spinning heads）.doc

1、本文档共16页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

冷旋压封头工艺守则（Code of practice for cold spinning heads）

冷旋压封头工艺守则（Code of practice for cold spinning heads） Cold spinning head process code Subject content and scope of application This standard provides the cold spinning two step production of pressure vessels, boilers and atmospheric containers head blank preparation, billet processing, press drum, flanging, head end heat treatment and other manufacturing requirements and inspection methods. This standard applies to our factory produces cold spinning Dg800 ~ Dg5200 all kinds of heads. Two Reference standard GB150 - 1998 steel pressure vessel JB/T4746 - 2002. Three Basic Requirements Three point one The head of a cold rotary pressure vessel shall comply with the regulations for the prosecution of the safety and technical regulations for pressure vessels, and the provisions of GB150 and relevant drawings and technological documents. Three point two Application of cold spinninghead materials for metal materials of carbon steel, low alloy steel and austenitic stainless steel elongation of not less than 18%. Four Technical content The types of spinning heads and the size of the blank are shown in table 1. Five Blank preparation Five point one Production of materials used should be consistent with head holding quality documents of relevant standards, for the low temperature pressure vessel and vessel head, the plate shall comply with GB150 1998 or JB4732 1995 provisions and drawings and process documents, it shall conform to the requirements of technical agreement or ordering. Five point two The surface and the blank end processing without scar, crack dissection and burr. Five point three The puzzle of unfitness of butt B (see Figure 1) shall not be greater than the thickness of the steel plate s 10%, and not more than 1.5 mm. The overlap edge B (see Figure 2) of the spliced composite plate is no larger than that of the steel plate The thickness of the 3%, and not more than 1 mm. Five point four Manufacturing units shall according to the acceptance of the steel plate quality