基于cras系统的发电机定子绕组端部模态试验研究 study on modal test of generator stator end winding based on cras.pdfVIP
- 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
- 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
基于cras系统的发电机定子绕组端部模态试验研究 study on modal test of generator stator end winding based on cras
10 广西电力 2008年第5期
基于CRAS系统的发电机定子绕组端部模态试验研究
onModalTestofGeneratorStatorEnd BasedonCRAS
Study Winding
陈 恒
CHEN 7
Heng
(广西电力试验研究院有限公司,广西南宁530023)
ElectricPowerTestandResearchInstitute 530023,China)
(Gt】a瑚p(i Co.,Ltd.,Nanning
摘要:为预防发电机定子绕组端部因谐振或其他原因造成的绑绳、支架固定螺栓和槽内紧固件松动以及线棒绝缘磨损的
现象发生,需准确测量定子绕组端部的振动量,预测发电机在实际工作状态下的振动幅度,应用CRAS动态分析系统对发电机
模态进行分析,评价发电机绕组端部整体结构动态特性,并以实例介绍了这种方法的应用,效果良好。
关键词:发电机;模态;C峪系统;频率;定子绕组
of in theabrasionofstatorbarinsulation
Abstract:InordertOavoidthe of bolt slot,and
looseningrope,fixingsupport,fastener
cau.sed of end orother vibrationvalueof statorend mustbe
the煳nance statorwinding reasons,the generator winding
by generator
of actual condition.Inthis
measured to thevibration under paper,CRASdynamic
preciselypredict magnitudegenerator working
is tO nlodeandevaluatethe characteristicof end strLletul-e.The
analysis appliedanalyzegenerator dynamic generatorwinding
system
show themetl-xxtiseffective.
methodisintroducedactual which that
by examples
system;frequency;statorwinding
KeyWOldS:generator;mode;CRAR
中图分类号:TM303.3文件标码:A文章编号:1671—8380(2008)05—0010—05
O 引言 益频繁。因此准确测量定子绕组端部的振动特性,
随着我国火电机组的装机容量日益扩大,发电 预测发电机在实际工作状态下的振动特性,及早采
andRan.
机单机容量已由原来的300MW发展到600IVIW、 取防范措施尤为重要。应用吣(Coder
您可能关注的文档
- 基于cim模型的电网拓扑分析 cim-based network topology analysis.pdf
- 基于cim模型的短路电流实时监视软件 real-time check of circuit breaker interrupting capacity based on cim.pdf
- 基于clifford代数传感器网络覆盖理论的平面目标覆盖分析 coverage analyses of plane target in sensor networks based on clifford algebra.pdf
- 基于cim模型的xml文件编辑器的实现 the technique to realize xml file editor based on cim.pdf
- 基于clarke变换的鼠笼异步电机故障诊断方法研究 study on method for fault diagnosis of squirrel cage induction motor based on clarke transform.pdf
- 基于cim模型的新一代集中式地县一体化电量采集系统研究 research of cim model in the new generation electric energy collection system.pdf
- 基于cim模型的智能变电站和调度中心互操作研究 interoperate research of the intelligent substation and dispatching center based on cim model.pdf
- 基于cmap的配电网潮流计算方法 power flow calculation of distribution system based on cmap structure.pdf
- 基于clifford代数的数字图像水印技术 a digital image watermarking algorithm based on clifford algebra.pdf
- 基于cmac的三关节机器人视觉伺服系统研究 research on cmac three-joint robot visual servo system.pdf
- 基于cps的中小型电动机故障诊断系统的实现 realization of medium and small size motor fault diagnosis system based on cps.pdf
- 基于crowbar保护的双馈感应发电机组的低电压研究 analysis of doubly-fed induction generator low voltage ride through based on crowbar protection.pdf
- 基于cream的电网人为可靠性定量分析方法 a quantitative method for human reliability in power system based on cream.pdf
- 基于c-r模糊模型pid控制及在过热汽温系统中的应用 pid control based on c-r fuzzy model for superheated steam temperature system.pdf
- 基于crowbar的双馈风力发电低电压穿越研究 doubly-fed induction generator low voltage ride through based on crowbar circuit.pdf
- 基于cs5451a跟踪频率采样的低压配变监控单元设计 low-voltage distribution transformer monitoring unit based on synchronous ac sampling with cs5451a.pdf
- 基于crowbar的双馈感应发电机低电压穿越的仿真研究 simulation of low voltage ride through of doubly- fed induction generator based on crowbar.pdf
- 基于crowbar的双馈风力发电系统lvrt仿真研究 simulation research for lvrt of dfig with crowbar.pdf
- 基于cs5460a的无轨电车智能电度表系统 research on cs5460a of intelligent kilowatt-hour meter system for trolley bus.pdf
- 基于cs5460a设计三相电能表关键技术研究 some key techniques in designing three-phase meter using cs5460a.pdf
原创力文档


文档评论(0)