回转窑开式齿轮的润滑的改进（To improve the lubrication of open gear of rotary kiln.）.docVIP

下载本文档

7
0
约5.13千字
约 7页
2017-08-16 发布于河南
举报
版权申诉

回转窑开式齿轮的润滑的改进（To improve the lubrication of open gear of rotary kiln.）.doc

1、本文档共7页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

回转窑开式齿轮的润滑的改进（To improve the lubrication of open gear of rotary kiln.）

回转窑开式齿轮的润滑的改进（To improve the lubrication of open gear of rotary kiln.） ======================================== page first ======================================== To improve the lubrication of open gear of rotary kiln. To improve the lubrication of open gear of rotary kiln. To improve the lubrication of open gear of rotary kiln. To improve the lubrication of open gear of rotary kiln. Author: an extensive analysis, Yang Weichen One Brief introduction of rotary kiln and open gear Our company is the production line 3, a 5000t / d cement clinker production line, December 20, 2004. The fire is put into production. Specification for rotary kiln With Four point eight * 72m, speed (max) 4.04r / min main motor power 6 30kW. The main drive for single drive gear for involute spur gear, the modulus M = 40mm, the number of teeth is Z respectively. 1 = 23, Z2 = 192; B1 = 700mm tooth width B2 = 600mm; lubricating oil Pool with lubricating oil tanker. ======================================== page second ======================================== Two Selection of lubricant In December 2004, the rotary kiln has just put into operation, in accordance with the requirement of the equipment manual, filling a domestic oil pool Brand No. 320 gear oil (equivalent to the old national standard No. 3 gear oil), which found that the vibration of the bearing block of the small gear The tooth is too large, high temperature, oil film forming bad tooth surface. But a good meshing, meshing clearance, contact length and width Are in the allowed range. Communicate with equipment manufacturing units and units that equipment installed in the running period, the partial vibration value Large tooth such as high temperature should be normal to imagine; after running, the oil film will be improved. In June 2005, a Prepare inspection found, small gear tooth surface has been pitting, tooth profile top has obvious signs of sliding friction; the gear tooth surface is Pitting, burrs protruding in rolling tooth wi