diy无线wifi的增益器（DIY wireless WiFi gain device）.docVIP

下载本文档

14
0
约1.14万字
约 10页
2017-09-05 发布于河南
举报
版权申诉

diy无线wifi的增益器（DIY wireless WiFi gain device）.doc

1、本文档共10页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

diy无线wifi的增益器（DIY wireless WiFi gain device）

diy无线wifi的增益器（DIY wireless WiFi gain device） I think you need to gain is DIY wireless WiFi. Here is the information you could use it. A selection The Internet to collect data to see the WIFI antenna, DIYER antenna and a lot of foreign made out of all kinds of really! A helical antenna, Yagi antenna, rhombic antenna, a grid antenna, antenna and canned... People see dazzling... After repeated screening, the ultimate goal of the produced antenna can lock. Select it as the DIY is mainly because of this antenna are easy and efficient! Production is suitable for beginners. Two, production The cylindrical antenna is convenient, because everyone must have cans, metal tube and the like. I just took a tin of milk powder production. The following is a reference to foreign WIFI website pictures painted drawings. The data are as follows: Center frequency = 2.445G The diameter of the cylinder is 127mm Cylinder length = 111mm Oscillator length = 31mm The vibrator from the cylinder bottom margin = 37mm Can be seen from the picture, feeder network connecting the shielding metal cylinder, the signal reflected to the oscillator through the cylinder, of course, the core oscillator is the feeder line, the core wire and the metal cylinder is insulated, it must pay attention to! In reference to foreign enthusiasts make WIFI antenna at the same time, I joined my mind: many lovers love with N or BNC in the cylinder, then the corresponding N head or BNC head at the junction of the feeder, for connection. But I feel that although the method is very convenient to use, but also caused a loss of signal (estimated 12DBI), especially in the range of 2.4G is more obvious! Therefore, mr7 decided to shield net direct welding on the cylinder (before welding to the shell polished), and as the core of the foam insulation. To minimize the loss. A little taste of green dedicated! Recommend the best before welding to find the root diameter slightly larger than the feeder tubes and the heat shrinkable sleev