zb206多功能电池容量测试仪使用说明书v1.2版本zb206+（Zb206 multi-function battery capacity tester manual v1.2 version zb206+）.docVIP

下载本文档

34
0
约1.03万字
约 10页
2017-09-05 发布于河南
举报
版权申诉

zb206多功能电池容量测试仪使用说明书v1.2版本zb206+（Zb206 multi-function battery capacity tester manual v1.2 version zb206+）.doc

1、本文档共10页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

zb206多功能电池容量测试仪使用说明书v1.2版本zb206（Zb206multi-functionbatterycapacitytestermanualv1.2versionzb206）

zb206多功能电池容量测试仪使用说明书v1.2版本zb206+（Zb206 multi-function battery capacity tester manual v1.2 version zb206+） Quick start instructions (default mode): 1. will be charged by the test battery (or charging charging Po Po USB output) positive and negative electrodes are connected to terminals BAT+ and BAT- blue, as far as possible short connecting line! To test instrument on DC 12V As the voltage (micro USB power supply section connected to 5V USB power), boot display preset current tester. 2. press S-- or S++ button to change the preset current in the range of 0.1-2.6A, right after the press the SK button to start testing (such as fault code Err*, please refer to following content tester) The intelligent selection of cell types and formulate termination voltage, RUN lights, digital display value from the capacity of Ah, energy Wh, voltage V and current A round. After the test, RUN The lights go out, stay in the Ah display flashes quickly with voice reminding. 3. after the completion of the SK button to press the tester to stop flashing alarm, press S-- or S++ button to switch to view the battery capacity Ah, energy Wh and discharge voltage is V, when again Press the SK button, just back to the tester boot state, can be repeated before operation under a battery test. Note: the test must be a key operation after the backup data can be removed, otherwise the results will always save a backup, even if the power is not clear! The meaning and way Err* error handling code: Err1: the battery voltage is too high, please make sure the battery before the test voltage is lower than 8.5V. Err2: the battery voltage is too low (below the set, please confirm the termination voltage) and reset the battery voltage, battery reverse is Err2. Err3: the battery does not support the current settings or line resistance is too big, please test with a smaller current, and to ensure that the line is thick and short, good contact between the electrodes. Err4: power tube damage, after the problem occu