九步完成机柜理线板的制作（Nine steps to complete the physical wiring cabinet）.docVIP

下载本文档

2
0
约6.03千字
约 4页
2017-09-08 发布于河南
举报
版权申诉

九步完成机柜理线板的制作（Nine steps to complete the physical wiring cabinet）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

九步完成机柜理线板的制作（Nine steps to complete the physical wiring cabinet）

九步完成机柜理线板的制作（Nine steps to complete the physical wiring cabinet） Nine steps to complete the physical wiring cabinet Method of making cabinet management plate is simple: measurement with twisted pair cable diameter, and additional 2-4mm after the formation of aperture management plate, then according to the distance between the hole and the hole in the choice of strength, longitudinal and transverse draw 5 lines, 5 lines drawn on the board after leaving a number of space determined after writing the length and width of plate. Cut or saw the excess, use the pistol drill at the intersection lineation to aperture determined by drilling 25 holes, with coarse paper will all edge chamfer, in the horizontal writing (or engraved) 1-5 number in the longitudinal write (or engraved) A-E number be accomplished. Management plate is a 25 hole plate (corresponding to the appropriate size 24 frame 5 * 5 hole arranging plate, you can also use 4 x 6, 8 x 8 specifications), single-sided printing, each hole can wear 1 horizontal twisted pair. You can imagine: when the twisted pair into the utility model, the relative position between each other is basically fixed, according to the bound its position is not prone to dislocation phenomenon, the phenomenon of cross was less prone to cable. Objective: using 24 1U frame, a cable from the frame (from the right rear frame on the back) to frame, from the bottom of the twisted pair wire harness out of the steering frame, the top of the twisted pair has been arranged to ensure the final 21 to 24 modules. 1. The wiring frame is fixed in place. The bracket is mounted behind it. The front panel will be printed with the line number on the distribution frame (or attached to the distribution frame). If the module of the distribution frame can be removed, then the module should be unloaded; 2, management plate positioning: management plate before threading first should determine its direction, make in the line board process does not need to reverse the