- 1、本文档共11页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
模拟地与数字地隔离问题(The problem of analog to digital isolation)
模拟地与数字地隔离问题(The problem of analog to digital isolation)
On the separation between digital and analog ground
1. the frequency of digital circuit is high, the sensitivity of analog circuit is strong, for signal line, the high frequency signal line is as far away from sensitive as possible
Sense analog circuit device, for ground wire, the entire PCB has only one node to the outside world, so it must be carried out inside the PCB
The problem of sharing the number of bits and the number of modules in the board is actually separate from the number and the analog. They are not connected to each other, but...
An interface (such as a plug) that connects PCB to the outside world. Please note that there is only one short connection between the digital and the analog
Connection point. There are also PCB on the ground, which is determined by system design. However, when making PCB boards, they usually do copper laying
The line and the line are all associated with the GND. Can you tell the difference between analog and digital after laying copper?
Is there only one join point?
The two places have different names, respectively, copper, and finally can be connected by an 10uH inductance or 0 ohm resistance.
The analog part is concentrated as far as possible and placed near the interface of other boards to reduce signal attenuation.
The number of lines is longer, it doesnt matter. Simulate copper first and then compress the entire plate digitally. simulation
The ground and the digital ground are automatically separated by a 1uH inductor or a 0 ohm resistor as a common site.
Two
In order to avoid detours and save time in electronic system design, the requirements of anti-interference should be taken into consideration and avoided
After the design is finished, the remedial measures against interference are also carried out. There are three basic elements of interference:
(1) an interference source, an element, a device, or a signal that produces interference, described in mathematical
您可能关注的文档
- 果树营养的年周期分配规律(Annual cycle distribution law of fruit nutrition).doc
- 果汁面膜(Juice mask).doc
- 果汁搭配2(Fruit juice 2).doc
- 果树营养分配要点(Main points of nutrient distribution in fruit trees).doc
- 果蔬营养与膳食平衡五点提示(Five tips on nutrition and diet balance of fruits and vegetables).doc
- 枣庄通病防治(Prevention and cure of common diseases in Zaozhuang).doc
- 架设教程新编译(Compile a new compilation of tutorials).doc
- 枸杞养生的正确吃法(The correct method of eating Chinese wolfberry).doc
- 枸杞子的功效及食用介绍(The effect of medlar and its food introduction).doc
- 枸杞海参鸽蛋汤(The sea cucumber soup wolfberry pigeon).doc
- 四川省德阳市罗江中学2025届高三考前热身化学试卷含解析.doc
- 山东省枣庄现代实验学校2025届高三下学期第五次调研考试化学试题含解析.doc
- 吉林省长春市十一高中等九校教育联盟2025届高三一诊考试生物试卷含解析.doc
- 2025届江苏省盐城市伍佑中学高考仿真模拟化学试卷含解析.doc
- 2025届广西贺州中学高考冲刺押题(最后一卷)生物试卷含解析.doc
- 安徽省池州市贵池区2025届高三第一次模拟考试生物试卷含解析.doc
- 宁夏银川一中2025届高三(最后冲刺)化学试卷含解析.doc
- 广东省广州市增城区四校联考2025届高考压轴卷化学试卷含解析.doc
- 2025届邯郸市第一中学高考生物必刷试卷含解析.doc
- 2025届安徽省安庆市石化第一中学高考仿真卷化学试卷含解析.doc
文档评论(0)