维修钳工考核试题库（Maintenance fitter examination questions bank）.docVIP

下载本文档

2
0
约2.87千字
约 3页
2018-05-30 发布于河南
举报
版权申诉

维修钳工考核试题库（Maintenance fitter examination questions bank）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

维修钳工考核试题库（Maintenance fitter examination questions bank）

维修钳工考核试题库（Maintenance fitter examination questions bank） Mechanical maintenance; fitter examination; examination question bank First, the theoretical assessment part Fill in the blanks: 1. The size of the slope is usually indicated by the angle between two straight lines (or planes). The size of the taper is determined by the angle of the cone, usually expressed by the ratio of the diameter difference between the two cross section of the cone and the distance between the sections. 2, any intersecting line has the following common characteristics: the intersecting line is the common cable of two basic body surfaces, and is a set of common points. Because the basic body has a certain range, the intersecting line is usually closed. 3, the method of intersecting lines has the following three kinds: the use of accumulation for intersecting lines; auxiliary plane method; auxiliary sphere method. 4, the use of auxiliary sphere method of intersecting lines must have three conditions: two, intersecting solid is rotating; two back axis should generally intersect; two times the axis of rotation parallel to a projection surface at the same time. 5, when the two revolving body has a common axis, the intersecting line is round; when the two cylindrical axes are parallel or the two conic common tops intersect, the intersecting line is a straight line. 6. The surface of the workpiece can be divided into expandable surface and not expandable surface. 7, the painting expansion diagram often asks for the general location of the actual length of the line segment, the actual length of the line can be used right triangle method, but in order to facilitate the mapping, often with the rotation method. 8, the surface of the column tube or the ridge lines are parallel lines, is on the surface. 9, a complete part drawing usually has the following contents: a set of views; adequate size; technical requirements; Title bar. 10, according to the processing order dimensioning, easy to look at the