徐州 kbz-500a真空馈电原理说明（Explanation of kbz-500a vacuum feeding principle in Xuzhou）.docVIP

下载本文档

6
0
约 12页
2017-10-07 发布于河南
举报
版权申诉

徐州 kbz-500a真空馈电原理说明（Explanation of kbz-500a vacuum feeding principle in Xuzhou）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

徐州 kbz-500a真空馈电原理说明（Explanation of kbz-500a vacuum feeding principle in Xuzhou）

徐州 kbz-500a真空馈电原理说明（Explanation of kbz-500a vacuum feeding principle in Xuzhou） ZK2-500/1.14-9 type low-voltage vacuum circuit breaker structure and working principle: font: small two As shown in Figure 3, the movable guide rod 1 of the switch tube 2 is connected with the wobble plate 4 by the adjusting bolt 5 and the contact spring 3. When the electromagnet 13 is not energized, the force of the reaction spring 15 is greater than the self closing force of the three switch tubes, and the switch tube 1 is in a disconnected position. When the electromagnet 13 is connected with the power supply, the armature 14 rotates with the swinging plate 4 to close the switch tube, and at the same time, the armature 14 pushes the pull rod 9, so that the buckle device 8 reaches the top of the half shaft 7. (conduction time electromagnet 100-200ms power device 8) electromagnet buckle resting on the half shaft 7, ensure the switch is closed, then to make the switch off must rotate axle half shaft can rotate to release, there are three institutions: undervoltage shunt tripping device and manual release and release mechanism. Undervoltage release is provided by the rectifier bridge 48V DC, so that it stays in the pull in state. When under voltage, overload, short circuit, leakage fault, intelligent protection to disconnect the power supply under pressure coil and undervoltage tripping device after power loss by the spring pushing core jumped upwards, the half shaft rotation, breaker, switch off. The shunt tripping device is usually no electricity, when under voltage, overload, short circuit, leakage fault, intelligent protection automatic connect shunt tripping device, shunt tripping device is the core of upward movement, drives the half shaft to make the circuit breaker tripping, disconnect switch. Manual tripping mechanism is used during maintenance or adjustment, or for electrical failure. Working principle of electrical system: I. protection of over planting, short circuit, leakage