第九节+一般阀门检修基本方法.ppt

  1. 1、本文档共49页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
电动闸阀检修 motor-driven gate valve overhaul 闸板阀研磨机 gate valve grinder 截止阀研磨 stop valve grinding 阀门检测 valve inspection 研磨抛光膏 grinding and polishing paste * 截止阀研磨 * 一般阀门检修基本方法 General Repair Methods for Valves 阀门种类 valve classification 按用途和作用分类 on function: (1)截断阀类主要用于截断或接通介质流。包括闸阀、截止阀、隔膜阀、球阀、蝶阀、针型仪表阀等。 Intercept valve mainly used for intercepting or connecting medium, including gate valve, stop valve, diaphragm valve, ball valve, butterfly valve and needle valve; (2)调节阀类主要用于调节介质的流量、压力等。包括调节阀、节流阀、减压阀等。 Control valve for regulating medium flow and pressure, including control valve, throttling valve and relief valve; (3)止回阀类用于阻止介质倒流。包括各种结构的止回阀。 Check valve is to prevent backflow; (4)安全阀类用于介质超压时的安全保护。包括各种类型的安全阀。 Safety valve is safety protection against overpressure. 按压力分类 on pressure (1)真空阀工作压力低于标准大气压的阀门。Vacuum valve (2)低压阀:公称压力 PN≤1.6 MPa 的阀门。LP valve (3)中压阀:公称压力 PN 为 2.5、4.0、6.4 MPa 的阀门。IP valve (4)高压阀:公称压力 PN 为 10.0~80.0 MPa 的阀门。HP valve (5)超高压阀:公称压力 PN≥100 MPa 的阀门。Super high pressure valve 按介质温度分类 on medium temperature (1)高温阀:用于介质工作温度 t > 450 ℃ 的阀门。HT valve (2)中温阀:用于介质工作温度 120 ℃ 的阀门。IT valve (3)常温阀:用于介质工作温度 -40 ℃ ≤ t ≤ 120 ℃ 的阀门。Normal temperature valve 气动蝶阀 pneumatic butterfly valve 截止阀 stop valve 闸阀 gate valve 铸铁闸阀 gate valve 电动调节阀 motor-driven control valve 气动调节阀 pneumatic control valve 1 修理阀门的要求 1 Requirement for Valve Repair 检查阀门损坏情况,确定是送修配车削,还是研磨(一般不平度大于0.5mm 要车光)。如有漏泄和裂纹,要进行阀座检查,必要时水压试验。 Check the damage of the valve; decide for lathing or grinding (usually larger than 0.5mm need to be machined). Check pedestal if there is leakage or crack. Conduct hydrostatic test if necessary. 检查阀杆是否凹凸不平,确定阀杆是否能续用。 Check if the valve rod is uneven and smooth, and make sure the valve rod can be continuously used. 闸板和门杆接合有无磨损。 If the joining of the disc and the valve rod has any abrasion. 螺母、阀体结合面是否平整。 If the combination surface of the nut and the valve body is flat. 2 阀门修理办法 2 Valve Repairing Method 门座有漏地方要焊补。 Welding repair the leak

文档评论(0)

shujukd + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档