鼠标外壳底壳具设计.docVIP

常熟理工学院毕业设计（论文） PAGE PAGE 1 鼠标外壳底壳实体建模及塑料模具设计说明书 摘要 本次设计采用的是UG 6.0工程应用软件，对鼠标底壳进行三维建模，分析鼠标底壳结构并根据零件造型设计一个一模两腔的注塑模具。在设计过程中需要对塑件材料进行选择，确定模具大小方面进行详细分析，选择的塑件材料为ABS，收缩率为1.005。选择标准模架以及标准件的确定，之后进行一些必要的强度校核，期间掌握了UG6.0的使用方法，掌握了其强大的三维建模功能。 关键词：UG6.0 鼠标底壳 三维建模 ABS PAGE PAGE 1 The mouse shell Bottom solid modeling and plastic mold design Abstract The design is UG 6.0 engineering application software, mouse Bottom three-dimensional modeling analysis of the mouse bottom shell structure designed according to Part Modeling a mold cavity injection molds. The material is ABS plastic parts in the design process need to choose a plastic piece of material, conduct a detailed analysis to determine the mold size, select the shrinkage rate of 1.005. Select the standard mold as well as the determination of standard parts, after the necessary strength check, mastered during the use of UG6.0 master the powerful 3D modeling capabilities. Key words:UG6.0;Mouse Bottom;Three-dimensional modeling；ABS PAGE PAGE 1 目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc354732184 1. 绪论 PAGEREF _Toc354732184 \h 2 HYPERLINK \l _Toc354732185 1.1 塑料成型在工业生产中的重要性 PAGEREF _Toc354732185 \h 2 HYPERLINK \l _Toc354732186 1.2 塑性模具的发展趋势 PAGEREF _Toc354732186 \h 3 HYPERLINK \l _Toc354732187 1.3 塑料模具的分类 PAGEREF _Toc354732187 \h 5 HYPERLINK \l _Toc354732188 1.4 毕业设计要达到的要求 PAGEREF _Toc354732188 \h 5 HYPERLINK \l _Toc354732189 2． 鼠标底壳的工艺分析 PAGEREF _Toc354732189 \h 7 HYPERLINK \l _Toc354732190 2.1 材料的选择 PAGEREF _Toc354732190 \h 7 HYPERLINK \l _Toc354732191 2.2 注射工艺选择 PAGEREF _Toc354732191 \h 8 HYPERLINK \l _Toc354732192 3. 模具的设计 PAGEREF _Toc354732192 \h 9 HYPERLINK \l _Toc354732193 3.1 概述 PAGEREF _Toc354732193 \h 9 HYPERLINK \l _Toc354732194 3.2 型腔的数量确定 PAGEREF _Toc354732194 \h 9 HYPERLINK \l _Toc354732195 3.3 注塑机的选择 PAGEREF _Toc354732195 \h 9 HYPERLINK \l _Toc354732196 3.3.1 注射量的计算 PAGEREF _Toc354732196 \h 9 HYPERLINK \l _Toc354732197 3.3.2 锁模力的校核 PAGEREF _Toc354732197 \h 10 HYP