- 1、本文档共5页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
115-02液压部分Information Codes 信息代码
1
Power ON check Error 电源打开检测错误
2
One or more joystick(s) is/are not in the neutral position after POWER ON
打开电源开关后一个或更多的操作手柄不在中位
4
The seat switch is not operated 座位开关没有动作
5
The lift slow input is operated.提升减慢输入动作
6
Lift stop feature is active 提升停止起作用
7
The sensor in the lift motor is indicating excessive temperature.
提升电机传感器显示过热
8
Slow speed reach慢速实现
9
Reach Back Inhibit 实现后退抑制
10
The lift enable signal to the module is missing. This could be because a UPA interlock has disabled lift.
没有到模块的提升确认。这可能是因为未计划的内锁使提升无效
11
BDI Cut-out active 智能显示仪表启动切断功能
12
Cage interlocks selected (UPA) 内部互锁被选(未计划的)
13
The main contactor is not energised and so the lift motor cannot run.
主接触器没有供电所以提升电机不能运转
15
The battery voltage during Lift has dropped below 37V
电池电压由于提升降到37V以下
17
The reach limit(s) are not programmed, calibrate mode.
达到限制没有编程,校准模式
18
There was no valve detected during the POWER ON checks.
电源打开后没有检测到阀
81
LAC No Hardware Enable input 没有硬件输入确认
82
LAC No Software enable via CAN 没有经过转接盒的软件确认
84
LAC Enable output is not set 输出确认没有设置
85
LAC No PWM request from LDC 没有从LDC来的功率模块需求信号
90
LAC Driver is in init sequence 驱动处在初始序列
91
LAC Driver init sequence is waiting for DC Link voltage 驱动初始序列等待直流
链接电压
92
LAC Drivers not initialized 驱动没有初始化
93
LAC Driver is blocked after overcurrent detection (1000ms) 检测到过电流后驱动锁定。
94
LAC Function inhibited 功能受限制
95
LAC Motor is not ready magnetized (Torque setpoint will be ignored )
电机没有被磁化(扭矩设置点被忽略)
96
LAC Motor is magnetized (normal operation mode)
电机被磁化(正常操作模式)
97
LAC Converters are locked due to permanent overcurrent detection (error 60)
由于检测到一直过电流导致LAC转换器锁定,
98
LAC PWM is off 功率模块截止
Warning Codes 警告代码
111
Battery is fully discharged and lift speed has been reduced
电池全放电和提升速度减慢
119
The calibration value for the joysticks has been corrupted
操作手柄校准值反了
120
Lift valve open circuit. 提升阀开路
121
Lower valve open circuit 低位阀开路
122
Reach valve open circuit 到达阀开路
123
Tilt valve open circuit 倾斜阀开路
124
Sideshift valve
文档评论(0)