单片机c语言程序库.docVIP

单片机库 姓 名：［鹿子庆］ 联系电话： 联系地址：［武汉理工大学］ 目录 TOC \o 1-5 \h \z HYPERLINK \l bookmark2 \o Current Document \h 1点亮第一个发光二极管 3 HYPERLINK \l bookmark4 \o Current Document \h 2不带参数的延时函数使灯闪烁 3 HYPERLINK \l bookmark6 \o Current Document \h 3带参数的延时惭数使灯闪烁 4 HYPERLINK \l bookmark8 \o Current Document \h 4左右移函数 4 HYPERLINK \l bookmark10 \o Current Document \h 5流水灯 5 HYPERLINK \l bookmark12 \o Current Document \h 6带蜂鸣器的流水灯 5 HYPERLINK \l bookmark14 \o Current Document \h 7第一个数码管显示8 7 HYPERLINK \l bookmark16 \o Current Document \h 8六个数码管同时亮一次显示0-F 7 9第一个数码管显示1,关闭，第二个数码管显示2,关闭，…… 8 HYPERLINK \l bookmark22 \o Current Document \h 10定时器中断程序 10 HYPERLINK \l bookmark24 \o Current Document \h 11键盘操作 13 HYPERLINK \l bookmark26 \o Current Document \h 12矩阵键盘扫描 16 HYPERLINK \l bookmark28 \o Current Document \h 13 A/D 19 HYPERLINK \l bookmark30 \o Current Document \h 14D/A 21 1点亮第一个发光二极管 # includereg52± sbitDl=PlAO; void main() { Dl=0; 2不带参数的延时函数使灯闪烁 #include reg52.h #define unit unsigned int sbit a=PlA0; void delay(); void main() { while(l) { a=0; delay(); a=l; delay(); } } void delay() unit i,j; for(i=500;i0;i-) for(j=110;j0;j-); 3带参数的延时函数使灯闪烁 #include reg52.h #define unit unsigned int sbit a=PlAO; void delay l(uint); void main() { while(l) { a=0; delay 1(400); a=l; delay 1(600); } } void delay 1 (unit xms) { unit i,j; for(i=xms;i0;i-) forG=110;j0;j-); 4左右移函数 # includereg52.h #define uint unsigned char uint a; void main() { a=0xba; while(l) a=a?l; 〃右侧移动改变为 即可 5流水灯 includereg52.h includeintrins.h #define uint unsigned int #define uchar unsigned char void delay 1 (uint); uchar aa; void main() { aa=0xfe; while(l) { Pl=aa; delay 1(500); aa=_crol_(aa, 1); void delay 1 (uint z) { uint i,j; for(i=z;i0;i-) for(j=110;j0;j-); 6带蜂鸣器的流水灯 # includereg52.h #include intrins.h #define uint unsigned int #define uchar unsigned char uchar temp,num,numl; sbit beep=P2A3; void delay(uint); void main() temp=Oxfe; while(l) { for(num 1 =O;num 1 3;num I ++) { for(num=0;num vnum++) { Pl=temp; bee