钢结构厂房地脚螺栓的埋置方法.pdf

  1. 1、本文档共8页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
精品文档 钢结构厂房地脚螺栓的埋置方法 The embedding of anchor bolts on the steel structure factory building 地脚螺栓的埋置是钢结构厂房施工的一大关键, 直接影响到上部钢结构厂房 的垂直度, 方正度。 若地脚螺栓的埋置偏差过大, 则会对后期的上部施工中的结 构螺栓,檩条螺栓,围梁螺栓的连接等造成很大的困难。在施工过程中,我们要 着重控制地脚螺栓的平面位置,垂直度及螺栓钉标高,以尽可能减少上述误差。 For direct influence on the perpendicularity and square, the embedding of anchor bolts is one of the most important points during the construction of steel structure building. There would be great difficulties in working on structural bolts, purline bolts, and girt bolts if there is any declination in embedding the anchor bolts. During construction, the great emphasis should be placed on the horizontal position, prependicularity and elevation of bolts in order to reduce such declination to the least.. 要求:平面位置误差:+ 3mm,螺栓顶标高误差:+ 3mm Basic requirements: Horizontal position declination: 3mm Anchor bolts top elevation declination: 3mm §1 须配备的设备,工具及施工人员: Working staff, Necessary equipment and Tools: 1.1 设备及工具: Equipment and tools: 光 学 水 准 仪 及 脚 架 , 标 尺 1 套 。 1欢迎下载 精品文档 Optical water level & horse and staff guage 1 光 学 经 纬 仪 及 脚 架 , 花 插 1 套 Optical theodolite, horse & flower brace 1 5 0 m 以 上 钢 尺 1 把 St e e l r u l e ( o v e r 5 0 m) 1 3 m- 5 m 钢 尺 2 把 Steel rule (3-5m) 2 线 锤

文档评论(0)

jjwhy + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档