- 1、本文档共36页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
PAGE
PAGE I
CC2105轴承座工艺分析及钻4-Ф11均布,沉孔Ф17深10孔夹具设计
摘要
专用夹具设计是每一个理工科学生必不可少的。本文设计的任务是CC2105轴承座工艺分析及钻4-Ф11均布,沉孔Ф17深10孔夹具设计。对零件的构造完全了解后,将毛坯的大小,加工方法,还有基准,加工的工艺路线都确定下来;之后按照事先设定的加工工艺路线,将粗基准,还有精基准分开,计算每一道工序的相关数据。
本次专用夹具设计是钻4-Ф11均布,沉孔Ф17深10孔。专用夹具设计的目的是将停机的时间缩短,提升生产率。夹具设计经过问题的提出;定位、夹紧方案还有装置的确定,加工时切削力等等。最后,绘制夹具装配图及所有非标零件图等。
设计夹具最关键是结构的合理性、工艺性,本次设计的夹具构造简单,紧凑,操作简单灵活。
关键词:专用夹具、CC2105轴承座、工艺、钻4-Ф11均布、沉孔Ф17深10孔
ABSTRACT
Special fixture design is essential for every science and engineering students. The design task of this paper is CC2105 bearing technology analysis and drilling 4-Ф11 uniform, Shen hole Ф17 deep 10-hole fixture design. After the complete understanding of the structure of the part, the size of the blank, processing methods, as well as benchmarks, process routes are determined; followed by the pre-set processing routes, the rough and fine benchmarks are separated, calculate each A process of data.
The special fixture design is drilling 4-Ф11 are uniform, Shen hole Ф17 deep 10 holes. The purpose of a dedicated fixture design is to reduce downtime and increase productivity. Fixture design through the question raised; positioning, clamping programs and equipment to determine the cutting force processing and so on. Finally, drawing fixture assembly drawings and all non-standard parts map.
The most critical design fixture is the structure of the rationality, technology, the design of the fixture structure is simple, compact, simple and flexible.
Key words:special fixture, CC2105 bearing, technology, drilling 4-Ф11 are uniform, Shen hole Ф17 deep 10 holes
PAGE
PAGE II
目 录 TOC \o "1-3" \h \z \u
摘要 I
ABSTRACT II
第1章 绪论 - 1 -
1.1 机床夹具的概述 - 1 -
1.2 机床夹具在机械加工中的作用 - 1 -
1.3 夹具设计的特点和基本要求 - 2 -
1.3.1 夹具设计的特点 - 2 -
1.3.2 设计的基本要求 - 2 -
第2章 CC2105轴承座机械加工工艺规程设计 - 3 -
2.1 零件的作用、设计基准及技术要求 - 3 -
2.1.1 零件的作用 - 3 -
2.1.2 零件的设计基准 - 3 -
2.1.3 零件的技术要求 - 3 -
2.1.4 零件的形位公差 - 4 -
2.2 零件的主要组成表面 - 4 -
2.3 零件的机械加工工艺性、材质及热处理要求
您可能关注的文档
- 12级主轴箱-车床主运动机械变速传动系统设计-N=25~1120;公比1.41;Z=12;P=5.5KW.docx
- 12级主轴箱-车床主运动机械变速传动系统设计-N=30~1320;公比1.41;Z=12;P=5KW.docx
- 12级主轴箱-车床主运动机械变速传动系统设计-N=31.5~1400;公比1.41;Z=12;P=4KW.docx
- 12级主轴箱-车床主运动机械变速传动系统设计-N=40~1800;公比1.41;Z=12;P=7.5KW.docx
- 12级主轴箱-车床主运动机械变速传动系统设计-N=71~900;公比1.26;Z=12;P=4KW.docx
- 180型复合管脱模装置(螺旋式)设计.doc
- 220型复合管脱模装置(螺旋式)设计.doc
- 350型复合管脱模装置(链条式)设计.doc
- 350型复合管脱模装置(螺旋式)设计.docx
- Ⅱ级转子数控加工工艺及铣削夹具设计.docx
文档评论(0)