项目7学习AD接口和DA.pptxVIP

项目7 学习A/D接口和D/A接口 ;任务1 用DAC0832实现方波、三角波、 锯齿波波形发生器;任务分析;任务实现;图7.3 DAC0832芯片的内部结构图;步骤2—硬件电路设计;波形发生器电路元器件清单如表7.1所示。;图7.5 集成运放LM324芯片的引脚图;图7.6 波形发生器电路板硬件实物; 锯齿波编程思路：先输出二进制最小值00H，然后按+1规律递增，当输出数据达到最大值FFH时，再回到00H重复这一过程。 源程序如下：;；************ 锯齿波程序 ******************* ；程序名：锯齿波程序PM7_1_1.asm ；程序功能：产生锯齿波信号输出 ORG 0000H AJMP START START：MOV DPTR，#7FFFH ；输入寄存器地址 AA： MOV A， #00H ；送转换初值 BB： MOVX @DPTR，A ；D/A转换 NOP ；延时 NOP CJNE A，#0FFH，CC ；判断最大值到否 SJMP AA CC： INC A AJMP BB END;正弦波编程思路： 源程序如下： ；********** 正弦波程序 *************** ；程序名：正弦波程序PM7_1_2.asm ；程序功能：产生正弦波输出,周期约256ms ,幅度约2.5V ORG 0000H LJMP MAIN ORG 0100H MAIN: MOV SP, #6FH PUB0：MOV R4，#00H PUB1：MOV DPTR，#TAB ；确定表首地址 MOV A，R4 MOVC A，@A+DPTR ；查表取输出参数 MOV DPTR, #7FFFH PUB2: MOVX @DPTR,A LCALL DELAY_1ms INC R4 CJNE R4，#00H，PUB1 ；判断一个周期到否 LJMP PUB0 ;TAB ：DB 80H,83H,86H,89H,8DH,90H,93H,96H,99H,9CH,9FH,0A2H,0A5H,0A8H,0ABH,0AEH DB 1H,0B4H,0B7H,0BAH,0BCH,0BFH,0C2H,0C5H,0C7H,0CAH,0CCH,0CFH,0D1H,0D4H,0D6H 0D8H DB 0DAH,0DDH,0DFH,0E1H,0E3H,0E5H,0E7H,0E9H,0EAH,0ECH,0EEH,0EFH,0F1H,0F2H,0F4H,0F5H DB 0F6H,0F7H,0F8H,0F9H,0FAH,0FBH,0FCH,0FDH,0FDH,0FEH,0FFH,0FFH,0FFH,0FFH,0FFH,0FFH DB 0FFH,0FFH,0FFH,0FFH,0FFH,0FFH,0FEH,0FDH,0FDH,0FCH,0FBH,0FAH,0F9H,0F8H,0F7H,0F6H DB 0F5H,0F4H,0F2H,0F1H,0EFH,0EEH,0ECH,0EAH,0E9H,0E7H,0E5H,0E3H,0E1H,0DFH,0DDH,0DAH DB 0D8H,0D6H,0D4H,0DlH,0CFH,0CCH,0CAH,0C7H,0C5H,0C2H,0BFH,0BCH,0BAH,0B7H,0B4H,0B1H DB 0AEH,0ABH,0A8H,0A5H,0A2H,9FH,9CH,99H,96H,93H,90H,8DH,89H,86H,83H,80H DB 80H,7CH,79H,76H,72H,6FH,6CH,69H,66H,63H,60H,5DH,5AH,57H,55H,51H DB 4EH,4CH,48H,45H,43H,40H,3DH,3AH,38H,35H,33H,30H,2EH,2BH,29H,27H DB 25H,22H,20H,1EH,1CH,1AH,18H,16H,15H,13H,11H,10H,0EH,0DH,0BH,0AH DB 09H,08H,07H,06H,05H,04H,03H,02H,02H,01H,00H,0