毕业论文--300MW汽轮机检修盘车传动系统设计.docx

陕西理工学院毕业设计论文 300MW汽轮机检修盘车传动系统设计 [摘要]随着我国火力发电大容量机组的逐步使用，汽轮机检修所用盘车的设计便引起了重视。以前的小机组盘车已经难以在大机组上使用。本设计就是关于现在国内普遍装机的300MW以上汽轮机检修时所用盘车传动系统的初步设计。该设计主要利用汽轮机转子上的联轴器法兰，采用剖分齿轮与其用螺栓连接，得以驱动转子，该盘车传动系统主要包括：电动机、减速器、齿轮传动。本设计的特点：摩擦阻力矩较大；传动比较大；两啮合齿轮中心距可以适当调节，得以保证齿轮正确啮合；支撑立柱高度可调。 [关键词]汽轮机；检修盘车；传动系统 Design of the 300MW Steam turbine overhaul dish vehicle drive transmission system Abstract： With Chinas coal-fired power generator capacity of use, dish vehicle drive design steam turbine overhaul gradually used drew attention. The dish vehicle drive small steam turbine unit set before in large unit has been difficult to use. This design is now installed on domestic common of more than 300 MW steam turbine overhaul car drive system used in the dish of preliminary design. The main advantage of the steam turbine rotor design on the flange, the coupling decomposing gear with bolt connection, and to drive the rotor, this dish car transmission system mainly include: motor, gear reducer, gear transmission. This design features: friction resistance torque is bigger; Transmission is larger; Two mesh center distance can proper adjustment to ensure the correct gear meshing. Support column height is adjustable. Key word: Steam turbine Verhaul dish vehicle drive Transmission system 第 PAGE \* MERGEFORMAT II页 共 = 2 \* ROMAN II页 目 录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc295666869 1.绪论 PAGEREF _Toc295666869 \h 1 HYPERLINK \l _Toc295666870 1.1选题背景 PAGEREF _Toc295666870 \h 1 HYPERLINK \l _Toc295666871 1.2汽轮机简介 PAGEREF _Toc295666871 \h 1 HYPERLINK \l _Toc295666872 1.2.1汽轮机发展历程 PAGEREF _Toc295666872 \h 1 HYPERLINK \l _Toc295666873 1.2.2国际汽轮机发展状况 PAGEREF _Toc295666873 \h 1 HYPERLINK \l _Toc295666874 1.2.3我国汽轮机发展状况 PAGEREF _Toc295666874 \h 1 HYPERLINK \l _Toc295666875 1.2.4汽轮机的工作原理 PAGEREF _Toc295666875 \h 1 HYPERLINK \l _Toc295666876 1.2.5汽轮机的配套设施 PAGEREF _Toc295666876 \h 1 1.2.6 HYPERLINK \l _Toc295666877 结构部件 PAGEREF _Toc295666877 \h 1 HYPERLINK \l _Toc295666878 1.2.7汽轮机种类 PAGEREF _