大雁矿业集团二矿0.6Mta新井的设计（含全套CAD图）.docVIP

需全套CAD或三维图 联系QQ 648328618 摘 要 本设计新井为大雁矿业集团二矿0.6Mt/a的新井设计，共有3层设计可采煤层，平均总厚度为5.7m。设计井田的可采储量为46.9Mt。服务年限为55a。划分两个水平开采。井田平均走向长2.5km，平均倾斜长4km，煤层平均倾角11°，属于缓倾斜煤层。 本设计矿井采用双立井的开拓方式，集中大巷布置方式。共划分12个带区，其中首带区为2个，达产工作面1个。本设计带区为北一，大巷装车式下部车场，综采机械化采煤。年工作日为330d，采用“三、八”式工作制，工作面长为190m，每刀进度为0.6m，每日割6刀。 提升设备为主井采用箕斗提升，副井采用罐笼提升。 由于井田倾斜长度较大，且为缓倾斜煤层，以及煤层地质条件等因素影响，决定本井田内全部采用倾斜长壁采煤法开采。 由于本人知识有限，缺乏现场经验。因此，本设计中难免会出现一些问题，请各位专家老师不吝指正。 关键词 可采储量 采煤工艺 倾斜开采 Abstract The task of this design is to construct a 0.6million tons new shaft for Shuangyashan Ming Administration.This mine has three minable Coal Seam,and its average thickness is 5.7meters.Designed field of minable capacity is 46.9 million tons. It can adapt for 55years, and is divided into two levels. Average alignment in farmland in well lengthways 2500 ms, average slant lengthways 4000ms, average rake angle in coal seam 11°, belong to the the slant the coal seam. This mine shaft is applied to double indined shaft development method; Layout of gathing gallergand mining district eross heading; The well farmland turns to is divided into totally 12 adopt the zone mines and 2 worked faces. This worked fece is west six worked face, words 330 days every year. Adapt “thee-eight” work situation, work face is 190 meters length of circle is 0.6meters, and times is 6 one day. Because the well farmland slant length is bigger, and incline the coal seam for the , and coal seam geology condition etc. factor effects, deciding this well farmland inside the complete adoption slant. Because my limit working ability and time. There must be lots of faults in this design. I plead with dirextors point them out and redify it, and I will accept it sincerely and humblely. Key words Recoverable reserves The technology of coal mining Adoption slant 目录 摘 要 I 绪 论 1 第1章 井田概况及矿井地质特征 2 1.1 井田概况 2 1.1.1 井田位置及范围 2 1.1.2 交通位置 2 1.1.3 地形与河流 2 1.1.4 气象 3 1.2 地质特征 3 1.2.1 矿区范围内的地层情况 3 1.2.2 井田范围内和附近的主要地质构造 4 1.2.3 煤层赋存状况及可采煤层特征 5 1.2.4 岩石性质、厚度特征 7 1.2.5 水文地质情况 7