- 1、本文档共24页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
Halliburton垂直钻井系统.ppt
“Confidential - For Internal Use Only. ? 2005 Halliburton. All Rights Reserved.” V-Pilot?Vertical Drilling System垂直钻井系统 Sperry Drilling Services September 2008 Jiu Sijun 酒思君 China DD Technical Advisor V-Pilot 垂直钻井系统 1 What is it? 什么是V-Pilot? Field Locations 油田位置 Field Test Result 试用结果 Successfully drilled 504 m (1,653 ft) in two runs under AFE target time. 在满足AFE时间的前提下,两趟钻完成了504米 Maintained low inclination 保持了较小的井斜 Completed entire interval with one roller cone bit – field average is 3-4. 一支牙轮钻头完成整个井段,而该油田平均需要3-4只 ROP up to 7 m/hr, at the high end of the field average. 机械钻速7m/h,是该油田的平均之最。 Tool proved largely insensitive to WOB – up to 20 tons used. 最大钻压达到20吨 Eliminated reaming and back-reaming due to outstanding hole quality 井眼质量光滑,减少了短起下钻时间和倒划眼时间 Field Test Result 试用结果 V-Pilot? Advantages 优点优势 V-Pilot? Advantages 优点优势 Bit stabilization utilized on V-Pilot? - Extended gauge length for smoother well bore profile. 使用V-Pilot?长保径钻头井眼光滑 Can be adapted to any bit choice. 可以使用任何钻头 WOB can be maximized without risk of ledging. 工具不受最大钻压的限制 Reduction in reaming and tripping time. 减少划眼时间和起下钻时间 Enhanced casing running. 提高下套管质量 Where is V-Pilot? Targeted for Use? 应用范围 V-Pilot 9600 Operating Parameters作业参数 Hole Size: 12-1/4”-22” 井眼尺寸:12-1/4”-22” Max WOB: 270 Kips 最大钻压:122吨 Max operating torque: 13,004 ftlbs 最大作业扭矩:27,116Nm Max differential Pressure: 720psi 最大压差: 4.96 MPa Flow range: 600 gpm – 1200 gpm 排量:600-1200gpm GeoForce? Motor Hydraulic Pump 水力泵 Hydraulic Pump 水力泵 Tool is meant to operate in sliding mode but will correct up to 5 RPM. 工具采用滑动模式进行作业,5rpm校正 5 – 25 RPM pads will remain retracted and will drill or ream like a straight motor. 5-25rpm时,垫片处于收位状态,如同一条直马达 Above 25 – 30 RPM centrifugal forces will pull the pendulum to one side inside the housing. One or two activation leavers will then be activated by the pendulum being off center and the hydraulics will extend one or two sets of pad pistons. 25-30rpm,钻具离心力将产生偏向一边的大钟摆力,V-Pilot的一个或两个垫片在大钟摆力的作用下偏离中心,液压将推动另外的一或两个
您可能关注的文档
最近下载
- 小学研究课题立项申报:基于小学生高阶思维发展的课堂微项目活动设计研究.docx
- 网站安全等级保护--应急预案.docx
- 输送带发展前景分析.pptx
- IPC-6018c,6018cs,6017,6016,6015,6013d,6012e,ds,da 英文资料分享.pdf
- 高中数学公式(经典).doc VIP
- 顶管施工测量方案.doc
- 2024年度医院中医肛肠外科科带教计划课件.pptx
- 全国青少年劳动技能与智能设计大赛赛题与评价标准.PDF
- 2021-2022学年福建省宁德市校际联盟八年级(上)第一次月考英语试卷(附答案详解).docx VIP
- 2023年(最全版)二级建造师考试真题及参考答案.docx
文档评论(0)