4010-14吨电动桥式起重机设计本科论文.docVIP

目录 摘要 1 绪论 3 1 起重机的技术参数 6 1.1 起重量与自重载荷 6 1.2 起升高度与起升载荷 7 1.3 跨度 8 1.4 运行速度 8 1.5 工作级别 8 1.6 起重机的材料 10 1.7 结构连接 11 1.8 生产率 11 2 起重机的机构 13 2.1 起升机构 13 2.2 运行机构 16 2.3 金属结构 18 2.4 性能参数表 19 3 起重机的零件 22 3.1 钢丝绳 22 3.2滑轮组 23 3.3 卷筒组 24 3.4 吊钩组 24 3.5 制动装置 25 3.6 减速机 26 3.7 联轴器 27 3.8 缓冲器 29 3.9 超载限制器 30 3.10 电器 31 4 起重机的安装与使用 33 4.1 起重机安装 33 4.2 机构的润滑 34 4.3 运转实验 35 4.4 起重机的交工验收 36 结 论 37 参考文献 38 致 谢 39  内容摘要：40/10-14吨电动桥式起重机主要由桥架，大车运行机构和装有起升，运行机构的小车组成。其桥架由钢板焊成的正规箱体主梁，端梁和走台等组成。主梁上铺设了供小车运行的钢轨。两主梁的外侧装有走台。一侧为安装及检修大车运行机构而设。另一侧为安装小车导电装置而设。在主梁下面悬挂着全视野的操纵室，操纵室内装有联动控制台和单个控制器，操纵室与走台装有斜梯，主梁连接在中间带有接头的两端梁上。大车运行机构采用分别驱动形式。起重机大车轮为四个，车轮与带有滚动轴承的角形轴承箱组装以后安装在端梁的两端。起重机小车由起升机构和小车运行机构所组成。此起重机的跨距大车为14m，小车3m，起重量主起升40t，副起升10t，工作级别A3，运行速度为大车1-10m/s，小车为2-20m/s。复合本起重机实际要求。 关键字：桥架；大车运行；小车运行；主梁；端梁；走台 Abstract：40/10-14 tons of electric bridge-style cranes consists mainly of bridge, traveling mechanism and equipped with lifting mechanism, the car. The bridge by steel box girder of regular welded, girders and Taiwan, etc. The car was laid for the girder of rail operation. Two of the girder with walk. Side for installation and maintenance during operation. The other side of the car for installation and conductive device. In view of the hanging below the control room, manipulation of indoor and individual controller with linkage console, room with Taiwan with inclined ladder, walk in the middle of the girder connection with joint at both ends of the beam. Traveling mechanism driven by respectively. Crane wheels for the big four wheels and rolling bearings with the angular bearing assembly installed on the client after both ends of the beam. Crane car by lifting mechanism and the car run institutes. This crane span for 14m, car 3m cart, weight lifting, Lord 40t 10t hoisting working level, and speed as A3 cart 1-10m/s, car for 2-20m/s. The actual requirements of crane. Key words: bridge, During operation, Cars run, Girders, End, Walking machin 绪论 被人们誉为“巨人之臂”，“画在天空中的弧”，“力与美的象征”的起重机，是广泛用于国民经济各部门进行物质生