ANSYS点焊构件有限元模拟命令流.docVIP

以下是本人做的一个点焊有限元分析的例子的命令流 ，注意本人用的是ANSYS，这里面有很多的命令流是废话，本人懒，就不做剪切了，其中重要的地方我都做了解释。将命令流复制粘贴到ANSYS的命令窗口按键盘上的回车键即可运行。这个案例用的是刚性短梁模拟焊点 ，希望对某些同志有一些参考意义。还要啰嗦一句，分析结果没有用实验验证过，正确与否，本人未知。 Finish 这三句是必须粘贴进去的 /clear /prep7 ET,1,SHELL181 这两行是单元类型 !* ET,2,BEAM188 !* R,1,0.0017, , , , , , 钢板厚度 RMORE, , , , , , , !* !* MPTEMP,,,,,,,, 这段是材料参数 MPTEMP,1,0 MPDATA,EX,1,,2.07E11 MPDATA,PRXY,1,,0.3 TB,BISO,1,1,2, TBTEMP,0 TBDATA,,300E6,490E6,,,, MPTEMP,,,,,,,, MPTEMP,1,0 MPDATA,EX,2,,2.0E11 MPDATA,PRXY,2,,0.3 TB,BISO,2,1,2, TBTEMP,0 TBDATA,,400E6,1000E6,,,, SECTYPE, 1, BEAM, CSOLID, , 0 SECOFFSET, CENT SECDATA,0.001,0,0,0,0,0,0,0,0,0 用于模拟焊点的短梁的半径，焊点的大小可在这里定义，这里是1mm RECTNG,0,0.1,0,0.16, 这段是模型的几何建模，本人是先画钢板，后画 /DIST,1,1.08222638492,1 线的，这短线代表了焊点 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST FLST,3,1,5,ORDE,1 FITEM,3,1 AGEN,2,P51X, , ,0,0,0.0015, ,0 /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST /VIEW,1,-1 /ANG,1 /REP,FAST /VIEW,1,,,1 /ANG,1 /REP,FAST FLST,3,1,5,ORDE,1 FITEM,3,2 AGEN, ,P51X, , ,0.06,0,0, , ,1 /DIST,1,1.08222638492,1 /REP,FAST /VIEW,1,,1 /ANG,1 /REP,FAST /VIEW,1,,,1 /ANG,1 /REP,FAST /DIST,1,1.08222638492,1 /REP,FAST /DIST,1,0.924021086472,1 /REP,FAST K,9,0.08,0.08,0, 画关键点