水性丙烯酸面漆的用途和使用说明.doc

水性丙烯酸面漆的用途和使用说明.doc

  1. 1、本文档共3页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
水性丙烯酸面漆的用途和使用说明

Intended Uses 用途 适用于钢结构防腐面漆,尤其适用于由于健康和安全原因不允许加入溶剂时。 Suited for painting steel structure as anti-corrosive finish,r, especially for the conditions where it is not permitted to use Solvent due to health and safety. Product Information产品简介 单组份水性面漆,不燃,对经良好的处理的钢材表面具有极优异的附着力,良好的防腐性,干性快,能用漆乳化漆,醇酸漆,水性环氧漆及氯化橡胶覆涂。浅黄色、蓝色、绿色、白色、灰色、红棕色等 One component water based finish, Excellent adhesion to varous old coat. Good anticorrosive property, fast dry. May overcoat with emulsion coating, alkyd paint, water based epoxy paints and chlorinated rubber paints Light-yellow, yellow, blue, green, white, gray, red-brown etc. Application details 产品数据 Volume Solids 固体份 About 35% 约35% Dry Flm Thickness干膜厚度 50-75microns 50-75微米 Theoretical Coverage 理论涂布率 5.9m2 /Kg at 50um dry film thickness 5.9平方米/公斤,以50微米干膜厚计 Practical Coverage 实际涂布率 Allow appropriate loss 允许适量损耗 Storage and Handling 施工详述 Mix Radio 混合比 One package 单罐装 Method of Application 施工方法 Airless Spray 无空气喷涂 Recommended 推荐采用 Brush or Roller 涂刷或辊涂 Recommended 推荐采用 Conventional Spray 传统喷涂 Suitable, but diluting is necessary 适用但需稀释 Thinner 稀释剂 Water,Maximum thining is 5% 自来水,最大稀释量5% Cleaner 油漆设备清洗剂 Water and specific cleaner 自来水和专用清洗剂 Pot Life 使用期 Not limit 没限制 Storage 贮存期 One year 一年 Drying time 干燥时间 Substrate Temperature底材温度 Touch Dry 表干 (min) Hard Dry 硬干 (H) Over coating Interval 覆涂间隔 Mix最短 Max最长 35℃ 25℃ ≤15 ≤30 ≤20 ≤24 2hours小时 4ours小时 Not limit 没限制 Storageand Handling 贮存与管理 Storage 贮存 dry and cool conditions 贮存于阴凉干燥处 Pack size 包装规格 20Kg in 20 liter container 20公斤装于20公升容器 Flash Poin

文档评论(0)

aicencen + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档