寄存器定义头文件内容简介.pptVIP

REG51.H、REG1211.H和REG1211.INC文件内容简介;标准8051单片机寄存器定义头文件REG51.H内容;sfr PCON = 0x87; sfr TCON = 0x88; sfr TMOD = 0x89; sfr TL0 = 0x8A; sfr TL1 = 0x8B; sfr TH0 = 0x8C; sfr TH1 = 0x8D; sfr IE = 0xA8; sfr IP = 0xB8; sfr SCON = 0x98; sfr SBUF = 0x99; /* BIT Register */ /* PSW */ sbit CY = 0xD7; sbit AC = 0xD6; sbit F0 = 0xD5; sbit RS1 = 0xD4; sbit RS0 = 0xD3; sbit OV = 0xD2; sbit P = 0xD0; /* TCON */ sbit TF1 = 0x8F; sbit TR1 = 0x8E; sbit TF0 = 0x8D;;sbit TR0 = 0x8C; sbit IE1 = 0x8B; sbit IT1 = 0x8A; sbit IE0 = 0x89; sbit IT0 = 0x88; /* IE */ sbit EA = 0xAF; sbit ES = 0xAC; sbit ET1 = 0xAB; sbit EX1 = 0xAA; sbit ET0 = 0xA9; sbit EX0 = 0xA8; /* IP */ sbit PS = 0xBC; sbit PT1 = 0xBB; sbit PX1 = 0xBA; sbit PT0 = 0xB9; sbit PX0 = 0xB8; /* P3 */ sbit RD = 0xB7; sbit WR = 0xB6; sbit T1 = 0xB5; sbit T0 = 0xB4; sbit INT1 = 0xB3;;sbit INT0 = 0xB2; sbit TXD = 0xB1; sbit RXD = 0xB0; /* SCON */ sbit SM0 = 0x9F; sbit SM1 = 0x9E; sbit SM2 = 0x9D; sbit REN = 0x9C; sbit TB8 = 0x9B; sbit RB8 = 0x9A; sbit TI = 0x99; sbit RI = 0x98; #endif;MSC1211寄存器头文件REG1211.H内容;sfr TMOD = 0x89; //定时/计数模式控制寄存器 sfr TL0 = 0x8A; //定时/计数器0低字节 sfr TL1 = 0x8B; //定时/计数器1低字节 sfr TH0 = 0x8C; //定时/计数器0高字节 sfr TH1 = 0x8D; //定时/计数器1高字节 sfr CKCON = 0x8E; //时钟控制寄存器 sfr MWS = 0x8F; //存储器写选择控制寄存器 sfr P1 = 0x90; //P1口寄存器 sbit T2EX = P1^1; //定时器/计数器2的外部控制输入 sbit T2 = P1^0; //定时器/计数器2的外部输入 sfr EXIF = 0x91; //外部中断标志寄存器 sfr MPAGE = 0x92; //存储器分页寄存器 sfr CADDR = 0x93; //配置地址寄存器 sfr CDATA = 0x94; //配置数据寄存器 sfr MCON = 0x95; //存储器控制寄存器 sfr SCON0 = 0x98; //串口0控制寄存器 sbit SM0_0 = SCON0^7; //UART0工作方式设定 sbit SM1_0 = SCON0^6; //UART0工作方式设定 sbit SM2_0 = SCON0^5; //UART0的SM2设定 sbit REN_0 = SCON0^4; //接收允许位 sbit TB8_0 = SCON0^3; //发送数据的第