60950 安规电压间距与高度温度规定.docVIP

＊ 線路與PCB上之FG接地符號為. ＊ INLET與EMI filter在線路圖上必需用虛線框起來標示. ＊ FUSE的Rating與警語需在PCB上標示,若空間不足時可在線路圖與使用手冊上註明Rating與警語. ＊ 安規管制之零件:跨一二次側與Bridge之前的零件;主Q的rating;一次側之磁材;Bulk cap rating; Output connector;Thermistor; Photo Coupler ;Fan;Case/散熱片/Thermal pad/Mylar的型狀尺寸 與開孔位置. 以上管制廠牌型號者需有安規證書才能認列(UL/CUL or CSA,TUV or VDE). ＊下列工作電壓(對應安全距離),工作溫度是安規check的重點. ＊.AC INPUT POWER的空間直線距離 Table 2H Minimun clearances for insulation in primary circuits,and between primary and secondary circuit Insulation working voltage (see 2.2.7) up to and including Nominal mains supply voltage 150V (300V Pollution degrees 1 and 2 (mm) Vpeak (Vin電壓)Vr.m.s. (Vin電壓) Operational (Fuse前,連接Fuse的零件)Basic Supplementary (All零件對Earth/case)Reinforced (跨一二次側的零件)0-71 0-50 1.0 2.0 4.0 72-210 51-150 1.4 2.0 4.0 211-420 151-300 1.5 2.0 4.0 421-840 301-600 3.0 3.2 6.4 (420V以上看Table 2J) 841-1400 601-1000 4.2 4.2 6.4 ＊. AC INPUT POWER的空間直線距離Table 2J Additional clearances Nominal mains supply voltage 150V ( 300V Additional（mm） Pollution degrees 1,2,3 R (跨一,二次側的零件) (跨一二次側的零件,零件工作電壓) Max. Vpeak 0-420 4 421-493 4.2 494-567 4.4 568-640 4.6 641-713 4.8 714-787 5.0 788-860 5.2 861-933 5.4 934-1006 5.6 1007-1080 5.8 1081-1153 6.0 1154-1226 6.2 1227-1300 6.4 1301-- 6.6 空間直線距離 Table 2 Minimun clearances in secondary circuit working voltage up to and including Nominal mains supply voltage 150V (300V Pollution degrees 1 and 2 (mm) Vpeak Vr.m.s. Operational (Fuse前,連接Fuse的零件)Basic Supplementary (All零件對Earth/case)Reinforced (跨一二次側的零件)0-210 0-150 0.7 1.0 2.0 211-280 151-200 1.1 1.4 2.8 281-420 201-300 1.6 1.9 3.8 421-700 301-500 2.5 2.5 5.0 701-840 501-600 3.2 3.2 5.0 841-1400 601-1000 4.2 4.2 5.0 ＊.AC / DC INPUT POWER的延面爬行距離Table 2L Minimum creepage distances (mm) Working voltage up to and including Vr.m.s. or d.c. (用Full Load,量零件工作電壓) Pollution degree 2 Material group IIIa+IIIb 零件如果有跨一,二次側時,以下距離要x2 101-125 1.5 126-150 1.6 151-200 2.0 201-250 2.5 251-257 2.6 258-264 2