N种扎头发方法.docVIP

N种扎头发方法。。 各种漂亮的扎头发方法 这个也是适合长头发的昂。。扎马尾,然后把马尾在头顶散开?像个毽子那样 储红燕?2010-07-26 12:36 这个步骤之前可以把头发刮毛,双手配合把散开的马尾向中间收成个包包,要注意包包的大小和留的头发长短喔,这个看自己头发情况定. 黄林云Mrs.Wentz?2010-06-03 23:32?（若打扰，请原谅）?回复 ? 把留下的头发顺着同一方向盘起来,这个步骤要特别注意,抓好的包包容易散掉. ? 收发尾。 ? 整理花苞。 成功哈 ? 这个适合长发MM哈。。先扎个马尾，越高越好，一般高度我觉得正面能看到皮筋就差不多.建议用手抓，扎出来比用梳子自然。 ? 把头发分成两股扭在一起,这个步骤之前可以把头发刮毛,扭的时候不要扭太紧了?松松的就好,这个步骤主要是让花苞看起来更花. 把扭好的头发围着扎起来的地方盘成个圆,也不要盘紧了噢. 彩片！正品推出！ 需要的MM可以加我QQ:1135395585 （若打扰，请原 把发尾收到里面?用皮筋扎住你也可以用发夹?我用发夹夹不太稳. 谅）?回复 用手整理花苞,就是往外拉下头发?注意是适当的拉,劲儿使大了当心前功尽弃额. 彩片！正品推出！ 需要的MM可以加我QQ:1135395585 （若打扰，请原 成功了哈 ? 韩式包头。。。来个侧面的 ? 1.首先把头发都梳起来，用手指梳哦，不要用梳子，这样比较自然?蓬松位置偏高一点 ? 2.然后用皮筋把梳起的头发绑起来?注意?最后一圈的时候不要把头发都弄出来 还没有照片描述... spacing of 100mm. C, line line line nearby. D, spare wire unified terminal strip Terminal (terminal strip at the top of the vertical, horizontal terminal strip from the harness to Terminal Pai end at the beginning), length to ensure as far as Terminal and set aside. After e, form a wire harness, cable, line. When the line should be in the core wire for better identification and marking on the cards will be prepared in advance, alternate core core content for the cable numbering. F, finish line, according to the corresponding terminal locations, wire one by one from the bunch out, pulling line, should be kept parallel to each other and more. Core dark as possible, determined in accordance with specific conditions, it is required that: neat, beautiful, shapely, pleasing to the eye. 7.6.2 wiring technology, out of the core wire according to Terminal position, cut off the excess, with wire stripping pliers or electrician knife stripped of insulation, so that connection. Stripping should not damage the copper core. B, core wire on the oxide and chip-insulated electricians knife scrape. C, core processing has been completed, thread round long nose pliers in a clockwise direction. Circle with the screw in the direction of spin in the same direction, circle should be appropriate, it is