缺陷等级与原因解析.docVIP

塑料件缺陷等级参照表 序号 缺陷名称 序号 缺陷名称 序号 缺陷名称 1 飞边 10 熔接线 19 表面光泽不良 2 变形 11 填充不满 20 3 困气 12 汽泡、包气 21 4 银丝 13 亮影、暗影 22 5 烧伤 14 擦伤、拉伤 23 6 缩痕 15 产品夹线 24 7 流痕 16 皮纹拉伤 25 8 开裂 17 顶白、顶裂 26 9 冲射纹 18 表面冷料 27 缺陷名称 飞边 缺陷 图片 缺陷等级 C 缺陷释义 在制件边缘产生的多余薄翅 缺陷图片 缺陷等级 产品一级面：A类 产品二级面：B类 产品三级面：C类 缺陷释义 制件表面产生黑点、黑条或沿制件表面呈炭化现象。 序号 产生原因 解决方法 1 料筒清洗不洁或有混杂物 认真清洗料筒使之干净，检查塑料有无杂质并及时清除 2 模具排气不良或锁模力太大 合理修整模具排气系统，减少锁模力 3 熔料中或型腔表面有可燃性挥发物 清理型腔表面，应无杂物及水分存在 4 塑料受潮、水解变黑 使用前烘干塑件，去除水分 5 染色不均，有深色物或颜料变质 合理配料 6 塑料成分分解变质 采用新材料 7 塑料温度过高，造成熔料分解、炭化 控制熔料温度 8 熔料加热时间过长，造成熔料分解炭化 控制熔料加热时间 缺陷名称 缩痕 缺陷 图片 缺陷等级 产品一级面：A类 产品二级面：B类 产品三级面：C类 缺陷释义 制件表面因材料收缩产生的凹 陷叫做缩痕。制件表面因材料收缩产生的凹 陷叫做缩痕。制件表面 spacing of 100mm. C, line line line nearby. D, spare wire unified terminal strip Terminal (terminal strip at the top of the vertical, horizontal terminal strip from the harness to Terminal Pai end at the beginning), length to ensure as far as Terminal and set aside. After e, form a wire harness, cable, line. When the line should be in the core wire for better identification and marking on the cards will be prepared in advance, alternate core core content for the cable numbering. F, finish line, according to the corresponding terminal locations, wire one by one from the bunch out, pulling line, should be kept parallel to each other and more. Core dark as possible, determined in accordance with specific conditions, it is required that: neat, beautiful, shapely, pleasing to the eye. 7.6.2 wiring technology, out of the core wire according to Terminal position, cut off the excess, with wire stripping pliers or electrician knife stripped of insulation, so that connection. Stripping should not damage the copper core. B, core wire on the oxide and chip-insulated electricians knife scrape. C, core processing has been completed, thread round long nose pliers in a clockwise direction. Circle with the screw in the direction of spin in the same direction, circle should be appropriate, it is best to slightly