铝合金表面处理研究现状.docVIP

铝合金表面处理的方法及应用 简彩娣 指导教师：the corrosion protection of aluminu[J]. Mater. Forum,1986,9 3 :163. [6]李国强,李荻.铝合金稀土转化膜的研究进展[J].材料工程,1998,7:3~5,8. [7]Atnott.Auger and xps studies of cerium Corrosion inhibition on7075 AluminumAlloy[J]. Application of Surface Science,1985, 22/23 :236. [8]Hinton B R W.Cerium Conversion Coatings for Corrosion Protection of Aluminum[J]. Materials forum,1989,9 3 :162~165. [9]邓志威.铝合金表面微弧氧化技术[J].材料保护,1996,29 2 :15. [10]薛文彬.铝合金微弧氧化陶瓷层膜的形貌及相组成分析[J].北京师范大学学报 自然科学版 ,1996,32 1 :67~70. [11]李吉祥,李炜.用等离子喷涂加激光重熔方法在铝合金表面溶覆陶瓷[J].表面技术,1996,25 3 :35~37. [12]梁工英.铝合金激光熔覆Ni-WC涂层的组织及耐磨性[J].中国激光,1988,25 10 :950~954. [13]李言祥,沈文.铝表面激光溶覆陶瓷原理和工艺的研究[J].表面技术,1997,26 6 :7~8,30. [14]司云森,孙勇.H2SO4溶液中表面改性铝电极的电化学性能研究[J].昆明理工大学学报,2001,26 2 :94~96. [15]石 磊,石　勇,董新民.铝及铝合金电镀[J].表面技术,2007,36 4 :87-88. [16]杨蔺孝,杨　岑.铝材耐磨耐烧蚀特种氧化成膜机理的研究与应用[J].电镀与环保,1992,12 2 :131. [17]李素琴,段绍范,段晓楠,等.铝合金脉冲硬质阳极氧化工艺与膜层性能的研究[J].材料保护,1994,27 3 :61. [18]顾德恩,陈金菊,冯哲圣,等.铝箔表面复合阳极氧化膜研究[J].功能材料,2004,5 35 :600-602. [19]刘世永,张会臣,高学敏,等.6063铝合金复合硬质阳极氧化及摩擦行为研究[J].轻合金加工技术,2004,32 4 :42-44. [20]赵　斌,董世知.铝合金化学镀Ni-P合金的研究进展[J].电镀与涂饰,2008,27 1 :24-26. [21]王艳芝.铝合金化学镀Ni2Fe2P2B,工艺研究[J].电镀与 环保,2002,22 4 :20-22. [22]郭瑞光,杨　杰,康　娟.铝合金表面钛酸盐化学转化膜研究[J].电镀与涂饰,2006,25 1 :46-48. and performance test copies of the record. If necessary, review should be carried out; 4 for spring hangers included simple spring, hangers and constant support hangers it should also be recognized as setting and locking of loads. 5 check the surface quality, folded layering and without cracks, rust and other defects. 5 after completion of the test and control drawing number one by one, by series baled. Color alloy steel parts, the parts marking installation location and rotation about the direction you want. 7.3.14. hangers installation 7.3.14.1 hanger layout a. a clear design of hanger should be installed strictly in accordance with the drawings and designs shall not be installed wrong, missing, etc. B. own arrangement of piping support and hanger set and selection