实战hp102激光打印机加粉图解.docVIP

实战激光打印机加粉图解 hp1020打印机加粉图解 １、拆下螺丝此主题相关图片如下：２、打开封装此主题相关图片如下：３、取下弹簧此主题相关图片如下：４、取下鼓芯 ,请取出后用纸包好尽量不要接触强光此主题相关图片如下：５、取下清洁辊 ,用纸擦干净此主题相关图片如下：６、取出小铁销此主题相关图片如下：７、拔出铁销此主题相关图片如下：８、拆开鼓体此主题相关图片如下：９、拧下螺丝此主题相关图片如下：１０、打开封盖此主题相关图片如下：１１、抽出磁辊，清空粉仓此主题相关图片如下：１２、装上磁辊此主题相关图片如下：１３、加粉此主题相关图片如下：１４、封盖此主题相关图片如下：１５、封装此主题相关图片如下：１６、拧好螺丝此主题相关图片如下：１７、取下定位簧此主题相关图片如下：１８、取下档板此主题相关图片如下：１９、拧下螺丝此主题相关图片如下：２０、清理废粉仓此主题相关图片如下：２１、拧下螺丝此主题相关图片如下：２２、装上清洁辊此主题相关图片如下：２３、装上鼓芯此主题相关图片如下：２４、钉入铁销此主题相关图片如下：２５、拧上螺丝，装上定位弹簧，完成 5L/6L激光打印硒鼓换粉图解 5L/6L激光打印硒鼓换粉图解一分离硒鼓打开机器取出硒鼓放在桌子上，首先摘下硒鼓上的一个弹簧，用斜口钳夹住一侧面金属销钉，向外用力拔出，两侧银色金属销钉拔出后可将硒鼓分成两部分，带有鼓芯一方是废粉收集件，带有磁辊一方是供粉仓。二更换鼓芯和刮板、清理废粉将废粉收集件中灰色感光鼓两侧的白色塑料卡子上的螺丝拧掉，将白色塑料卡子向外拔出，鼓芯就可以取出来。再把放电辊取出来，拧掉刮板上的两个螺钉拿出刮板，把废粉全部清理干净，再把刮板、放电辊、感光鼓按拆前的状态恢复好 注意鼓芯及两端的白色塑料卡子和放电辊方向不能反 。轻轻转动鼓芯数圈，鼓面上应干干净净。若鼓面上有残粉，应及时更换刮板。三灌装墨粉如果您的硒鼓是没有灌过墨粉的原装硒鼓第一次灌粉，这次灌粉就不需要清理粉仓和磁辊，否则必须把粉仓和磁辊上的墨粉清理干净。取出粉仓上的塑料盖，把天野4v/4vc墨粉摇一摇再慢慢的倒入粉仓内，盖好塑料盖，轻轻的转动磁辊数圈，磁辊应能均匀的吸附墨粉。四组装硒鼓将供粉仓和废粉收集件按拆开时位置安装复原，插好两侧金属卡销上好小弹簧。硒鼓装好后，应推开感光鼓挡板，向上轻转鼓芯侧面齿轮数圈，鼓面残留墨粉即被清除，装机即可使用。 I signed with the Bank of the qilu Bank loan contract contract conventions, and I use scheme, I would request the loans in words until I opened personal settlement account with your Bank account , uses loan for 。 Loan operation, business unit name: account number: loan funds from these personal settlement account into the account of a payment. Loans in accordance with the following payment methods to pay. One, lender trustee payment. Delegate qilu Bank loan funds of the borrower to meet the stipulation of the contract the following borrowers, counterparties, commitment funds, regulatory compliance, legal, and willing to take the pay disputes, loss and other consequences of the delegate. Payee account number Bank name amount purpose II, borrowers own payment methods. Qilu Bank according to the borrowers withdrawal request to loan funds disbursed directly to the borrowers account, and independently by the borrower payments to borrowers wh