LCD1602四线编程实现.docVIP

LCD1602四线编程实现——51单片机和LPC23xx系列单片机 (2009-05-07 19:49:49) 转载 标签： 四线 51单片机 lpc23xx it 分类： 第一次调4线的LCD1602，比较困难，或者因为延迟不对，或者因为命令错误，我足足用了一天时间，搞定了4线的1602编程实现。这里提供51单片机和LPC23XX系列单片机的程序。51的程序是我上网找的，可以参考里面的实现步骤，可以直接仿真，但是不知道烧到板子里是否可以。LPC23XX系列单片机的程序可以直接烧写板子里运行，注意里面的管脚定义，因为在proteus里没找到对应的芯片，这里不知是否可以仿真。 #include reg51.h sbit LCM_RW=P2^0; //定义引脚sbit LCM_RS=P2^1;sbit LCM_E =P2^2; #define LCM_Data? P1 #define Busy 0x80 //用于检测 LCM 状态字中的 Busy 标识 void WriteDataLCM(unsigned char Data);void WriteCommandLCM(unsigned char Command); void LCMInit(void);void DisplayOneChar(unsigned char X, unsigned char Y, unsigned char DData);void DisplayListChar(unsigned char X, unsigned char Y, unsigned char code *DData); void Delayms(unsigned int n);void dellay(unsigned int? h); unsigned char code blog_adr[] = {EDNchina};unsigned char code email[] = {tengjingshu@126.com}; void main(void) {??????? //Delay400Ms();??? //启动等待，等 LCM 讲入工作状态??????? LCMInit();???????? //LCM 初始化??????? DisplayListChar(3, 0, blog_adr);?? DisplayListChar(0, 1, email);??????? while(1);} //写数据 RS=H,RW=L,D0~D7=数据,E=高脉冲void WriteDataLCM(unsigned char Data)?{??????????? LCM_RS = 1;?????? LCM_RW = 0;??? LCM_E? = 0;??? LCM_Data =(Data 0xF0);??? LCM_E? = 1;?????? dellay(100);???? //短暂延时，代替检测忙状态??? LCM_E? = 0;?????? LCM_Data =(Data 0x0F)4;?????? LCM_E? = 1;??? dellay(100);??? LCM_E? = 0;} //写指令 RS=L,RW=L,D0~D7=指令码,E=高脉冲void WriteCommandLCM(unsigned char Command){dellay(100);?????? //短暂延时，代替检测忙状态????? LCM_RS = 0;?? LCM_RW = 0;?? LCM_E? = 0;?? LCM_Data =( Command 0xF0);?? LCM_E? = 1;????? dellay(100);?? LCM_E? = 0;????? LCM_Data =( Command 0x0F )4;????? LCM_E? = 1;?? dellay(100);????? LCM_E? = 0;} //读数据 RS=H,RW=H,E=H//读状态 RS=L,RW=H,E=H//由于不要检测忙，所以读数据和读状态两个函数省略 void LCMInit(void)???? //LCM 初始化{????? LCM_Data = 0;????? Delayms(15);????? WriteCommandLCM(0x03); //三次显示模式设置，不检测忙信号????? Delayms(5);????? WriteCommandLCM(0x03);????? Delayms(5);????? WriteCommandLCM(0x03);????? Delayms(5