佳能 CANO IP2780 连供改装说明.docVIP

佳能 CANON IP2780 连供改装说明（供参考）取出待改装的CANON 815 816 墨盒。撕去墨盒上盖上的标贴。准备给彩色墨盒进行钻孔，注意红色位置（在墨盒透气口的下面）。其他在透气孔位置上扩孔。给黑色墨盒扩孔。扩孔时钻头要垂直于墨盒上盖，如扩好后边缘有塑料毛刺，可用美工刀修平整。钻好孔后的墨盒。如是全新原装墨盒，可不用给墨盒加墨水。用过的墨盒先要给墨盒加墨水（注意颜色千万不要加错了），加好墨水后静置20分钟，打印光盘中的4色色块图片，进行测试，4色能正常打印后才能进行下一步的操作。拿出AB胶（504、509胶水，一般五金店有售。），A，B胶水各拧出一点点，搅拌均匀后涂在下图的红色箭头处。密封红色墨水透气口。在墨盒扩孔的地方塞入白色密封胶圈。拿出连供外盒，把管线对折，夹子夹好，小胶塞塞入左孔，然后加入墨水。（4仓加入墨水的颜色与墨盒内墨水的分布有关，此款以CANON IP2780为例，墨水颜色如上图。）加好墨水后，塞上加墨口胶塞。合上外盒彩罩，将外盒平倒（如上图，注意平倒方向），目的是排空恒压仓中的墨水。竖起外盒，打开外罩，将小胶塞全部右移。（这步不要忘记操作了，不然出墨不畅，打不出墨水。）把管线上的夹子拿下，让外盒中的墨水冲入管线，快到管线末端时，对折管线，夹子夹好，不让墨水流动。修剪管线长度，注意管线对应颜色不要搞错了，然后装上弯头。修好的效果可参考下图。把墨盒装上打印机笔架内。盒上墨盒上盖。按上图固定管线，注意管线到左右距离的长度要合适。合上打印机上盖，安装完成。通电后进行打印测试。----------------------------------------------------------------------------------------以下部分主要给打印量大的用户作参考，打的少和动手能力差一些的用户可不进行改装。废墨管的接出红圈的地方用一字起撬一下，拆开托纸板。再用一字起撬一下，拆下打印机上盖。取下机器4个镙丝，打开打印机。拉出白色废墨胶管，在胶管下方钻个孔。穿出胶管。 the provisions of Hunan province safety production supervision and management responsibilities (Hunan Zhengban made 2013 No. 4), resolutely implement the safety production of the party with responsibility, a pair of responsibility. Two is issued safety production administration and inspection to promote the responsibilities bear safety production supervision departments strictly and effectively assumed responsibility. The three is the establishment of enterprise production safety hidden With self correction self reporting system, promote the enterprises to implement the main responsibility for production safety. The four is the introduction of strengthening county safety production supervision ability construction work, promote safe production responsibility to the grassroots. 3, strict accountability and target management. Adhere to the who is in charge, who is responsible for the pipe industry must pipes, pipe production and management must control safety management business must be safe principle, the implementation of