毕业设计(论文)－立体激光固化造型机机械结构设计.docVIP

PAGE IV 摘要 自20世纪80年代中期以来，光固化快速成型技术的发展与应用越来越广泛和深入，光固化成型机的需求也越来越大。由此，本论文针对cps250型激光固化成型机的机械结构进行了设计，包括：1、X-Y扫描机构；2、Z轴升降机构；3、刮刀机构，并且对其中的部分结构进行了改进。X-Y方向的平面扫描运动和刮刀的水平运动由原来的精密同步带传动改成精密滚珠丝杠传动，使其在行程较长时不出现抖动，有利于保证扫描精度，运动稳定。采用直线步进电机直接连接滚珠丝杠，响应更加快速准确，同时因无中间部件，使机械结构简单化，精度较高。 通过对立体激光固化造型机机械结构的设计，使得其运动和传动更加合理和平稳，进而使其在生产过程中能够更好的进行生产。 关键词:立体激光固化 扫描机构 快速成型 传动 Abstract This article specifically for three-dimensional modeling of light-cured structural design of mechanical systems. X-Y scanning normally used to screw drive. Through the motor rotation, with another even reached the screw shaft, through to the X and Y to the two motors of rotation to achieve XY to scan; Z to the table, also by the screw and a rail. Z to the table by the extension units, columns, screw composition, its transmission is through the same motor rotation axis is to pass even reached the screw by screw to achieve the rotation of the table move up or down. Through the three-dimensional modeling of light-cured in the design and mechanical systems, making their campaigns and drive more reasonable and stable, then in the production process so that it can better carry out production. Key word: SLA Scanning agencies Rapid Prototyping Transmission 目录 TOC \o 1-3 \h \u HYPERLINK \l _Toc1036 摘要 PAGEREF _Toc1036 I HYPERLINK \l _Toc7325 Abstract PAGEREF _Toc7325 II HYPERLINK \l _Toc31487 目录 PAGEREF _Toc31487 III HYPERLINK \l _Toc24967 第1章 绪论 PAGEREF _Toc24967 1 HYPERLINK \l _Toc31506 1.1 快速原型技术简介 PAGEREF _Toc31506 1 HYPERLINK \l _Toc4216 1.1.1 RP的基本构思 PAGEREF _Toc4216 1 HYPERLINK \l _Toc3559 1.1.2 几种典型的快速成型技术 PAGEREF _Toc3559 2 HYPERLINK \l _Toc29095 1.1.3 各种成型方法简介及对比 PAGEREF _Toc29095 3 HYPERLINK \l _Toc13165 1.2 快速成型精度概述 PAGEREF _Toc13165 4 HYPERLINK \l _Toc25469 1.3 立体激光固化成型（SLA）的成型原理 PAGEREF _Toc25469 5 HYPERLINK \l _Toc32212 1.4 SLA的国内外发展现状 PAGEREF _Toc32212 6 HYPERLINK \l _Toc20266 1.5 本次设计的主要工作 PAGEREF _Toc20266 7 HYPERLINK \l _Toc23114 1.5.1 主要设计任务 PAGEREF _Toc23114 7 HYPERLI