6_VW_USER程序分析V1.00详细分解.ppt

下载文档 降价啦

20
0
约 21页
2016-12-19 发布于湖北
举报
版权申诉
保障服务

6_VW_USER程序分析V1.00详细分解.ppt

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

SERVO-P SYSTEMVW 程序分析 Ver：1.0 * 1.程序分析······································································3 2.VW_SMC.DAT································································· 4 3.VW_SMC.SRC································································· 6 3.1 程序结构·······························································6 3.2 VW_SMC··································································7 3.2.1 程序信息····························································· 7 3.2.2 查看当前工具是否为焊钳(PAR2) ·································7 3.2.3 用户输入的缸径及焊钳类型信息································· 7 3.2.4 计算用户输入的中间位置信息（PAR3) ························· 8 3.2.5 计算用户输入的平衡缸压力信息（PAR4）······················ 9 3.2.6 计算用户输入的焊钳压力信息（PAR5）··························9 3.2.7 通过输入板厚计算钢板接触位置(PAR6) ······················· 11 3.3 VW_SMC_I·····························································12 3.3.1 焊钳工具号判断·····················································12 3.3.2 使能重新输入判断··················································12 3.3.3 焊钳参数赋值······················································· 13 3.3.4 更换电极帽后钢板位置自动补偿·································15 3.3.5 电极修模后钢板位置自动补偿··································· 15 3.3.6 子程序调用··························································16 3.4 SMC_Hand···························································· 17 3.4.1 焊钳号判断·························································· 17 3.4.2 焊钳标定运动······················································· 17 3.4.2.1 速度及枪型设定···················································· 17 3.4.2.2 焊钳标定执行条件··················································18 3.4.2.3 执行相关动作，信号等待···········································19 3.4.2.4 对焊钳相关参数赋值················································20 3.4.2.5 执行动作，跳出判断················································21 * 1.程序分析伺服系统程序固件程序（Ver7C）接口程序（VW