《单片机-4章C51语言-数码管按键-11-4.pptVIP

分析： 将显示码循环输出到P0口即可实现循环显示。但由于数字0～9的显示段码没有规律可循，需要采取查表方式进行操作： 循环10次 ？ N 延时 循环指针i 赋值(10) P0 ←数组[i] Y ①将显示码按序存放在一个数组中, 顺序号与代表的显示字符相对应。（如，char led_mod [ ]={x1,x2,….,xn） ②通过循环变量指定待送出的数组元素 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. #include reg51.h //包括一个51标准内核的头文件 char led_mod[ ]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; //LED显示字模 void delay(unsigned int time) { unsigned int j = 0; for(;time0;time--) for(j=0;j125;j++); } void main(void) { char i = 0; while(1) { for(i=0;i=9;i++) { P0=led_mod[i]; delay(500); } } } //延时程序，定义一个延时参数 //延时参数作为循环初值， //内循环循环125次，大约为1ms //主函数 //循环10次 //每次取出一个段码 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4.3.4 8位数码管动态扫描 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 朗逸实验箱共阴极8位， 共阳极1位数码管 2个锁存器，暂存段码，暂存位码 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4.3.4 8位共阴数码管动态扫描 8位数码管分别显示不同数#includereg52.h #define DataPort P0 //定义数据端口 程序中遇到DataPort 则用P0 替换 sbit LATCH1=P2^2; //定义锁存使能端口 段锁存 sbit LATCH2=P2^3; //定义锁存使能端口 位锁存 unsigned char code dofly_DuanMa[ ]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; // 共阴极，显示段码unsigned char code dofly_WeiMa[ ]={0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f};//分别对应相应的数码管点亮,即位码 //1111 1110, 1111 1101, 1111 1011, 1111 0111，……0111 1111 void Delay(unsigned int t); //函数声明 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. main() { unsigned char i=0; while(1) { DataPor