API602紧凑型闸阀特点..doc

API 602紧凑型闸阀特点API 602 Compact Gate Features  (1) 明杆 - 易于观察开启-关闭状态。(1) Rising Stem – easily visible open-close indication. (2) 润滑油附件 - 轭架套管配置润滑油附件，降低磨损和操作扭矩。(2) Grease Fittings – yokesleeves equipped with grease fittings to minimize wear and operating torque. (3) 旋启式螺栓 - 使得维护和填料更换更加简便易行。(3) Swing Bolts – facilitate easier maintenance and packing replacement. (4) 填料函 - 可配置备选灯笼环和润滑油注射器。(4) Stuffing Box – optional lantern rings and grease injectors are available. (5) 阀盖连接 - 封装垫圈结构。(5) Bonnet Joint – encapsulated gasket design. (6) 阀体 - 全流道(全端口)，重型阀体，符合API 602标准的壁厚，最大限度延长使用寿命。(6) Body – full ported, heavy duty body with API 602 wall thickness for maximum service life. (7) 阀座环 - 分离式重型、全流道(全端口)环，易于维护。(7) Seat Rings – separate heavy duty, full ported rings for easy maintenance. (8) 手轮 - 易于操作的大手轮。(8) Handwheel – large handwheels for easy operation. (9) 轭架套管 - 配置416不锈钢或铝青铜材料。(9) Yokesleeves – furnished in 416 stainless steel or aluminum-bronze. (10) 压盖 - 两件式压盖/压盖法兰，自行对准调节，防止由于压盖翘起而造成阀杆损坏。(10) Gland – two-piece gland/gland flange is self-aligning to eliminate stem damage from cocked gland. (11) 阀杆 - 精加工阀杆配置后座结构。(11) Stem – precision machined stem has a backseat design. (12) 楔形闸板 - 全导向楔形结构，精密配合阀体阀座，实现最有效的关闭。(12) Wedge – fully guided wedge precision fitted to body seats for maximum shutoff. (13) 连接端口 - 可提供法兰、螺纹或焊接连接端口供用户选择。(13) End Connections – choice of flanged, threaded or socket weld ends.  备选件OPTIONS  润滑油注入器和套环GREASE INJECTOR AND LANTERN RING 连接端口END CONNECTIONS  承插焊Socket Weld 法兰Flanged 螺纹Threaded 软阀座T形阀座环SOFT SEATED T TRIM SEAT RING 　　所有闸阀都可以配置备选的聚四氟乙烯(PTFE)阀座环。这种模铸聚四氟乙烯环粘合在阀座表面的阀座环槽内，最大限度延长使用寿命。这种结构对于要求紧密性关闭的低温应用特别适用。　　All gate valves are available with optional PTFE seat rings. The molded PTFE ring is bonded into a seat ring groove in the face for maximum service life. This design is excellent for lower temperature service where tight shutoff is required. API 600螺栓阀盖闸阀特点API 600 Bol