BFT-2操作手冊.docVIP

BFT—2操作手册 北京华能通达能源科技有限公司 目录 1.0 BFT-2设备连接安全须知························4 1.1人身安全···································4 1.2、仪器安全··································4 2.0 BFT-2设备连接前的准备工作····················4 2.1.工具的准备································4 2.2.测量32芯阻值和绝缘·······················5 2.3.检查仪器外观、密封面及O型圈··············6 3.0 BFT-2设备连接过程····························8 4.0 BFT-2地面检查过程····························8 4.1地面仪器检查······························9 4.2控制台、升压电源及调压电源的绝缘电阻检查··12 4.3 外接电源检查·····························12 4.4．地面连接································12 4.5井下仪器检查·····························12 5.0 BFT-2设备上井前的准备工作···················13 6.0、BFT-2设备上井井场环境及井眼条件···········13 7.0 BFT-2测试器操作流程························14 7.1仪器地面检查······························14 7.2井眼条件··································14 7.3、作业过程································15 7.3.1下井前井口准备························15 7.3.2仪器对零·······························15 7.4开始测井·································15 7.5测井完成后注意事项························18 7.6作业过程的着重点··························19 7.7 资料整理·································19 8.0 BFT测井过程安全质量监控···················20 8.1电缆地层测试测井质量控制标准·············20 8.2 BFT-2测井情况···························21 9.0 BFT测井过程应急处理·······················21 9.1 仪器遇阻·································21 9.2 防止仪器和电缆的粘卡·····················22 9.3 解卡·····································22 10.0 BFT测井后的保养与维修····················22 11.0故障判断与排除····························24 1.0 BFT-2设备连接安全须知 1．1人身安全 仪器本身质量很大，为确保仪器在移动、连接、运输过程中的人 身安全和仪器安全，要求至少两人以上抬动仪器，且需穿戴防护用品。 仪器要放置在平稳的支架上，防止仪器滚动、损伤仪器和人员。 仪器通电时，内部有380V交流电，切忽触摸电源变压器、仪器接头等，以免电击。 维修仪器时，使用接地良好的平台、电烙铁。人体接触仪器前，触摸一下与大地接触良好的金属，释放静电。 井口电缆有一千伏交流电压，井下电子线路的伽玛计数电源有一千多伏直流电压，维修和使用中必须注意人身安全。保持机箱和仪器外壳的良好接地。不要伸手触及加电的机内电路，特别是带高压的零部件。 1.2、仪器安全 仪器在运输前，特别注意不允许带压力传感器运输。应将石英压力传感器拆掉，装入专门的包装箱，随仪器到达后，再将传感器安装到仪器。 仪器在测井时，采用地面组装。仪器的连接端口要连接牢固。防止仪器脱落和连接部位进井液。 仪器测井前后，必须检查各仪器间连接部位的密封件是否完好。如果不够完好，必须更换密封件，方可下井。 注意仪器高温高压指标，尽可能避免仪器在超出指标以外的环境下工作，避免淋雨和暴晒。 仪器