光敏树脂固化成型机起升机构设计【毕业论文+CAD图纸全套】.doc

摘 要 阐述了快速成型技术的加工过程，突破了传统的加工方法上的许多限制，在主要的几种快速成型工艺方法中，光固化成型法已成为当今研究发展最成熟、应用最为广泛的RP典型技术。光固化快速成型以光敏树脂为原料，计算机控制紫外激光按零件的各分层截面信息在光敏树脂表面进行逐行扫描，使被扫描区域的树脂薄层 光聚合反应而固化，形成零件的一个薄层。文中设计的起升机构借鉴了螺旋起升机的工作原理。 螺旋传动起升机基本原理是利用电机，通过减速器减速后，带动螺母旋转，转化为丝杆的轴向运动，从而推动物体上升。主要内容如下：对光固化快速成型系统控制原理进行了研究；设计起升机构；选择电动机；设计减速机构；控制电路的设计；简要阐述在流水线作业中，螺旋传动原理等。 关键词： 光固化快速成型；电动；螺旋传动 Abstract Expounds the machining process of the rapid prototyping technology, break through the traditional processing method many of the restrictions on, in a few of the main rapid prototyping technology method, uv-curable ChengXingFa has become the research and development the most mature, most widely used RP typical technology. Light curing photosensitive resin in rapid prototyping as raw materials, computer control laser by part of ultraviolet each layered section information in lightsensitive resins surface manufacture progressive-scan, make be scanning the area light thin layer of resin curing polymerization, forming parts of a thin layer. The design of lifting mechanism for the spiral up the work principle of mining. And the basic principle is that the motor drives the rotary nut through the deceleration agencies, screw into the axial campaign, and then lift the objects .The main contents as follows: research the principle of spiral jack and the principles and methods of the spiral lifting, design the agencies of spiral lifting; motor choice; design deceleration agencies; select keys and bearings, design the control circuit; describe the principle of the screw jack on the assembly line operation. Keywords: Stereo Lithography Apparatus; Electrical; Spiral drive 目 录 1 绪论 1 1.1快速成型技术 1 1.2光固化快速成型技术的控制原理及应用 1 2 设计方案的确定 4 2.1螺旋传动设计方案 4 2.1.1螺旋传动概述 4 2.1.2螺旋传动方案的确定 5 2.2减速传动机构设计方案 6 3 传动系统的设计 7 3.1螺旋传动部分计算 7 3.1.1螺杆直径的计算 7 3.1.2螺纹部分强度计算 7 3.2电机的选择 9 3.2.1电动机功率计算 10 3.2.2传动效率 10 3.2.3确定电机转速 11 3.3减速机构的设计 12 3.3.1材料的选择 12 3.3.2蜗轮蜗杆传动基本尺寸 13 3.3.3 强度校核 16 3.3.4蜗轮蜗杆传动中的作用力分析 16 3.3.5实际传动动力参数 17 4 辅助装置的设计 1