CADKey_Surfacer_Fuction_List.doc.doc

CADKey 曲面功能： 截面線曲面(general curve surface) 規則曲面(rule surface) 網格線曲面(curve mesh surface) 邊界曲面(edge curve surface) 掃掠曲面(swept surface) 平移曲線(tabulated cylinder) 旋轉曲面(surface of revolution) 導圓角曲面(fillet surface) 變化半徑導圓角曲面(fillet surface with spine curve) 接合曲面(blend surface) 增量曲面(offset surface) 邊界曲面(boundary surface) 拔模曲面(draft surface) 節點/向量曲面(point/vector surface) 截裁曲面(trimmed surface) Surfacer功能指令 Point選項 8-0 導論 8-1 點群資料擷取選項 (Extract Point) 8-1-1 圈選點群 (Circle-Select Point) 8-1-2 封閉的曲線圈選點群 (Point Within Curves) 8-1-3 以方塊範圍選點群 (Extract Points in Box) 8-1-4 框選Grid Cloud點群 (Extract Sub Grid Cloud) 8-1-5 均勻分割點群 (Slice) 8-1-6 擷取Scan Line點群 (Extract Scan Lines) 8-1-7 歸類點資料為Scan Line (Break into Scan Lines) 8-2 點群資料編輯選項 (Create From Clouds) 8-2-1 點群資料相加 (Add Point Clouds) 8-2-2 點群掃描( Scan Clouds from Scans) 8-2-3 點群資料相減 (Subtract Point Clouds) 8-2-4 由兩筆點群資料求平均點群 (Average Point Clouds) 8-2-5 Offset點群資料 (Offset Clouds) 8-2-6 投影點群到平面上 (Project to a Plane) 8-3 點群資料擷取剖面資料 (Cross Sections) 8-3-1 平行 (Parallel Cross Section) 8-3-2 放射狀 (Circular Cross Sections) 8-3-3 任意方向的 (Interactive Cross Sections) 8-3-4 沿著曲線的 (Curve Aligned Cross Sections) 8-3-5 三角網格的 (Cross Section) 8-3-6 投影線段到點群上 (Cloud by Projecting Curve on Cloud) 8-3-7 Z軸網格投影點群 (ZGrid Cloud) 8-4 點群特徵資料擷取 (Dense Feature Extraction) 8-4-1 點群特徵資料擷取 (Sharp Edge) 8-4-2 軟體以顏色擷取點群 (Color Based) 8-5 建構點群 (Construct Points) 8-6 由曲線產生點群 (Create From Curves) 8-6-1 由曲線產生點群 (Sample Curve) 8-6-2 由Cross曲線產生點群 (Cross Section Curve) 8-6-3 量測點群、曲線間最短距離 (Closets Point on Curve) 8-6-4 以曲線為基準產生對稱點 (Symmetry Point from Curve) 8-7 由曲面產生點群 (Create From Surfaces) 8-7-1 由曲面取樣產生點群 (Sample Surface) 8-7-2 在誤差範圍內由曲面取樣產生點群 (Sample Surface to Tol) 8-7-3 沿軸向產生Grid點群 (Grid Surface) 8-7-4 由Cross曲線產生點群 (Cross Section Surface) 8-7-5 量測點群、曲線間最短距離 (Closest Point on Surface) 8-7-6 以曲面為基準產生對稱點 (Symmetry Point from Surface) 8-8 由點群產生三角網格 (Polygon Operations) 8-8-1 將點群計算成三角網格 (Polygonize) 8-8-2 將三角網格回復成點群 (Unpolygonize) 8-8-3 將三角網格Normal方向反轉 (Reverse Polygon