2012年国监延续状葱垄册继续教育试题第一套(72分).docVIP

?第1题(2分)单选题 喷射混凝土施工时，所用的速凝剂、其初凝时间不应超过（????????????????? ）  HTMLCONTROL Forms.HTML:Option.1 ?A.?10min HTMLCONTROL Forms.HTML:Option.1 ?B.?15min ? HTMLCONTROL Forms.HTML:Option.1 ?C.?5min ? HTMLCONTROL Forms.HTML:Option.1 ?D.?3min ? ??第2题(2分)单选题 ? 屋面细石混凝土防水层表面平整度用2m靠尺和楔形塞尺检查，其允许偏差为（????????????? ）  HTMLCONTROL Forms.HTML:Option.1 ?A.?2mm  HTMLCONTROL Forms.HTML:Option.1 ?B.?3mm  HTMLCONTROL Forms.HTML:Option.1 ?C.?4mm HTMLCONTROL Forms.HTML:Option.1 ?D.?5mm ??第3题(2分)单选题 ? 轻型木结构工程中普通圆钉的最小屈服强度应符合设计要求，每种长度的圆钉至少随即抽取（????????? ）枚，进行受弯试验  HTMLCONTROL Forms.HTML:Option.1 ?A.?5  HTMLCONTROL Forms.HTML:Option.1 ?B.?10 ? HTMLCONTROL Forms.HTML:Option.1 ?C.?15 ? HTMLCONTROL Forms.HTML:Option.1 ?D.?20 ? ??第4题(2分)单选题 ? 承重木结构原木材质为Ⅱa级的受拉构件或拉弯构件，扭纹斜率不大于（?????? ）  HTMLCONTROL Forms.HTML:Option.1 ?A.?6 HTMLCONTROL Forms.HTML:Option.1 ?B.?8 HTMLCONTROL Forms.HTML:Option.1 ?C.?12 HTMLCONTROL Forms.HTML:Option.1 ?D.?15 ??第5题(2分)单选题 ? 层板坯料指接的间距，对于手拉构件，当应力达到或超过设计值的75%保嗔诘牟惆逯渚嗬胗ξ????? ）mm  HTMLCONTROL Forms.HTML:Option.1 ?A.?10 HTMLCONTROL Forms.HTML:Option.1 ?B.?15 HTMLCONTROL Forms.HTML:Option.1 ?C.?20 HTMLCONTROL Forms.HTML:Option.1 ?D.?25 ??第6题(2分)单选题 ? 结构胶合板每层单板的节孔眼垂直木纹方向不得超过（????????? ）mm  HTMLCONTROL Forms.HTML:Option.1 ?A.?56  HTMLCONTROL Forms.HTML:Option.1 ?B.?66  HTMLCONTROL Forms.HTML:Option.1 ?C.?76  HTMLCONTROL Forms.HTML:Option.1 ?D.?86 ??第7题(2分)单选题 ? 钢主梁、次梁及受压杆件的垂直度和侧向弯曲矢高的检查数量按同类构件数抽查10%也挥π∮冢??? ）个 HTMLCONTROL Forms.HTML:Option.1 ?A.?1 HTMLCONTROL Forms.HTML:Option.1 ?B.?2 HTMLCONTROL Forms.HTML:Option.1 ?C.?3 HTMLCONTROL Forms.HTML:Option.1 ?D.?4 ??第8题(2分)单选题 ? 当钢材的表面有锈蚀、麻点或划痕等缺陷时，其深度不得大于该钢材厚度负允许偏差值的（????????? ）  HTMLCONTROL Forms.HTML:Option.1 ?A.?1/4  HTMLCONTROL Forms.HTML:Option.1 ?B.?1/3  HTMLCONTROL Forms.HTML:Option.1 ?C.?1/2 ? HTMLCONTROL Forms.HTML:Option.1 ?D.?3/4 ? ??第9题(2分)单选题 ? 木结构防腐的构造措施应符合（???????????????? ）要求  HTMLC