木工平面刨(手压刨)安全操作规程.docVIP

木工平面刨(手压刨)安全操作规程 木工平面刨安全操作规程提要：每次刨削量不得超过，被刨的木料必须紧贴”靠山”，进料速度保持均匀.经过刨口时，按在料上的手用力要轻，禁止在刨刃上方回料 来自地产E网 木工平面刨安全操作规程 一、平刨机的安全防护装置必须齐全有效，否则禁止使用. 二、刨料时两腿前后叉开，保持身体稳定，双手持料.刨大面时，手应按在料上面;刨小料时，可以按在料的上半部，但手指必须离开刨口50mm以上，严禁用手在料后推送跨越刨口进行刨削. 三、被刨木料的厚度小于30mm，长度小于400mm时，应用压板或压棍推送.厚度在15mm，长度在250mm以下的木料，不得在平刨上加工. 四、每次刨削量不得超过，被刨的木料必须紧贴”靠山”，进料速度保持均匀.经过刨口时，按在料上的手用力要轻，禁止在刨刃上方回料. 五、被刨材料长度超过2m时，必须有两人操作;料头越过刨口200mm后，下手方准接料，接料后不准猛拉. 六、被刨木料如有裂破，硬节等缺陷时，必须处理后再施刨.刨旧料前，必须将料上的钉子，杂物清除干净.遇木槎，节疤要缓慢送料.严禁将手按在节疤上送料. 七、活动式的台面要调整切削量时，必须切断电源和停止运转，严禁在运动中进行调整，以防台面和刨刃接触造成飞刀事故. 八、换刀片应拉闸断电. 九、刀片和刀片螺丝的厚度，重量必须一致，刀架夹板必须平整贴紧，合金刀片焊缝的高度不得超过刀头，刀片紧固螺丝应嵌入刀片槽内，槽端离刀背不得小于10mm.紧固刀片螺丝时，用力应均匀一致，不得过紧或过松. 十、机械运转时，不得将手伸进安全挡板里侧移动挡板.禁止拆除安全挡板进行刨削.严禁带手套操作. 十一、木料需要调头时，必须双手持料离开刨口后再进行调头，同时注意周围环境，防止碰伤人和物. 来自地产E网 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX stud