测量放线监理工作要点.docVIP

测量放线监理工作要点 测量放线监理工作要点提要：对承包人提交的施工测量报验单及测量资料要进行复核测量。检查验收合格的，及时给予书面认可；发现有差错 来自 测量放线监理工作要点 ①监理工程师在熟悉设计文件和图纸的基础上，会同承包人、设计单位或勘测部门在现场交接中线控制桩和水准点，并要求承包人对所有测量控制桩和水准点进行有效的保护，直到工程竣工验收结束。 ②要求施工单位进行水准点、导线方位角，进行复核测量，确保原始定线方位、水准点高程的数据准确无误。若发现有连续两个以上原始基准点或基准高程失效、损坏时，应通过业主由设计勘测单位补定。 ③对承包人提交的施工测量报验单及测量资料要进行复核测量。检查验收合格的，及时给予书面认可；发现有差错，应及时通知承包人重测，合格后再予以书面认可。 ④监理工程师应对承包人所做的加密控制点、辅助基线、临时水准点和施工放样的测量工作，进行现场监督、检查、复核并认可。 3、质量标准、检测频率与方法 ①水准线闭合差： 质量标准：高程控制视线长在50～80m，水准测量闭合差为±12（L为水准线长度km）。 检测频率：沿路线往返各一次。 检测方法：用水准仪具测量。 ②方位角闭合差： 质量标准：允许偏差为±40。n为测站数，单位为（”）。 检测频率：1个测回。 检测方法：用Dj6级经纬仪。 ③道路中心线桩恢复： 质量标准：桩距在直线段宜为15-20m；曲线地段为10m。平、竖曲线起止点和地形变化点必须加桩。 检测频率：丈量不少于2次。 检测方法：用钢尺量。 ④道路横断面： 质量标准：直线段为路中心线垂直方向；由线段为垂直于所测点的切线方向，其宽度不得小于设计图纸的规定。 检测频率：沿路线长度方向，每100m抽测1处。 检测方法：用钢尺量。 来自 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, ha