钢筋工程施工技术措施.doc

钢筋工程施工技术措施 钢筋工程施工技术措施提要：钢筋配制前必须先进行钢筋翻样，经有关人员审核后，由钢筋场根据情况进行碰焊或使用原料，施工单位按要求进行下料 源自管理资料 钢筋工程施工技术措施 钢筋焊接一般采用闪光对焊，结构竖向钢筋对接采用电渣压力焊，不便焊接或允许搭接时按规范进行搭接。 所有钢筋的领用，必须同时领取出厂材质合格证和公司试验室做的试验报告单，确认合格，否则不准使用。钢筋领出时，要核对数量、标牌、型号、规格等，并分类堆放整齐，挂好标识牌。 钢筋配制前必须先进行钢筋翻样，经有关人员审核后，由钢筋场根据情况进行碰焊或使用原料，施工单位按要求进行下料。下料必须准确，加工尺寸、形状符合图纸和规范。加工成型的钢筋表面要洁净、无损坏、无油污；挂牌分类堆放整齐；在使用前应将铁锈、泥土等清理干净，带有颗粒或片状老锈的钢筋不准使用。 在钢筋使用时，钢筋的规格、型号必须符合设计要求；当需进行钢筋代换时，需经有关人员签证同意。 钢筋的调直和弯钩，应符合施工规范和设计要求。 工程开工前要对所有要焊接的钢筋进行焊接工艺评定。每批钢筋焊接必须按规定进行可焊性试验，合格后办理可要批量焊接，并且所有焊工必须持证上岗，证件必须按时复审合格，否则不准上岗。钢筋焊后要按规定抽头试验。 在钢筋绑扎和安装时，钢筋交叉点应用铁丝绑扎牢固，角部应全部绑扎，大面积的钢筋网可按梅花状扎牢，保证受力钢筋不移动。在钢筋配制、绑扎时要保证钢筋接头按规范规定相互错开。梁、柱箍筋若无特殊要求，应与主筋垂直，并与受力筋绑牢。 钢筋绑扎成型后，要求工艺美观，保持钢筋表面的清洁，不准有污泥、油渍等。 钢筋绑扎时要按图纸垫好保护层，当图纸无要求时应符合《钢筋砼工程施工及验收规范》的规定。 源自管理资料 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality,