高效静电技术原理—辉光电离.docxVIP

高效静电技术原理—辉光电离电晕放电起晕阶段 在一定的直流电压作用下，负极性电晕或正极性电晕均在放电电极附近聚焦起空间电筒及高能电子，为了将臭氧的产生量降至最低。 2)流光电离阶段 起晕阶段完成后，随着直流电压的进一步升高，高能电子及空间电荷将进一步转化为自由电子及自由电荷，在此阶段，正电荷被驱往远离电极的空间形成正离子；臭氧也主要产生于此阶段。 3）辉光电离阶段 在电极达到流光电离电压后，电场继续加强，负离子被吸进电极，出现脉冲电晕电流，而正离子则扩散到间隙空间，随着电晕电流的脉冲频率增加，即进入辉光电离阶段，此时两极附近形成柱状空间电荷区，电荷的能量与稳定性达到最强。而将静电场控制在辉光电离阶段则是静电净化的核心技术之一。4）火花放电阶段 若在辉光电离阶段后持续长高电场强度，复式脉冲电流将持续增强，最终导致间隙击穿。高效静电技术原理安装注意事项净化系统内通风量应在净化器额定处理风量内；1the amount of ventilation in the purification system should be within the rated air flow rate of the purifier;净化器安装应保证水平，否则，净化器收集的油会被风机吸出，或放油时不能将净化器内的油放尽； installation should ensure that the level, otherwise, the oil purifier collected by wind suction, or put the oil can not be put in the oil purifier;管道内风速应设计在8-10m/s; wind speed pipe should be designed in 8-10m/s弯头中线半径≥1.5D（若不满足此条件，则变径管风阻会成倍增大） elbow radius is larger than 1.5D midline (if not meet this condition, it will increase the drag reducing pipe)变径管（小变大）斜边与轴线夹角≤70（若不满足此条件，应考虑合理安装导流板。否则，净化器净化效率将大幅度降低而不能达到国家排放标准） tube (small and large) bevel angles with the axis is less than or equal to 70 (if you do not meet this condition, should consider the reasonable installation guide plate. Otherwise, the purification efficiency of the purifier will be greatly reduced and can not meet the national emission standards.变径管（大变小）你斜边与轴线夹角≤150（若不满足此条件，应考虑合理安装导流板。否则，净化器不能发挥器效能）。如图所示；7 tube (big or small) your bevel angles with the axis is less than or equal to 150 (if you do not meet this condition, should consider the reasonable installation guide plate. Otherwise, the purifier can not play the effectiveness of the device. As shown in figure;净化器进风口之前应有一段≥2.5D的直管（若不满足此条件，应考虑合理安装气流均布板和导流板。否则，净化器不能发挥器效能 ）；Before the 8 air purifier should be a straight over 2.5D (if this condition is not met, should consider the reasonable layout and installation flow guide plate. Otherwise, the purifier can not play the effectiveness of the device;风机应安装减振器；fan should be installed vibration damper;风机进出风口应安装软连接； wind turbine inlet and outlet shou