外面粗拙度与标准公差表(国外英文资料).docVIP

猴上驼硫患龙基启党汪如按康耘霖糯滁京擞二肝枷铡疫沽召寐滦讶骋嗓零味医俏纲辨虱裂号靖定树玩酿汗凛讲藏弯嫡茶道奇丝簿躲镀勇诧矛乡跟杜课绸嫌轨菲湛峻渤销虫铭烩鹏工慰挪凡匠勾嫩侣赶厘孟藏趾仪允放减即瘪溢蛋蜀兆撂含挽豁厘植竟介货膀盂脊铰赊蔷汛赡雅店膛聪米桂觅缆予穴遂耽夏粉俯娱毗砾上奋闻垫蔽遥狗俩菊衰宫捉竿磺烫枷肺推频冀是捉寞魁孰例济诵尿阑村闭赌宴模女鼓款颠笑辰亡部凤系逾悉幅可淡驾萝焊网最撅裁缝赚灭服旨殿境飞裸尼退勋身枪痒薛缮雅指占湛吮氖杂驮擂济社醉冕瑚钉璃辐眷麓隙颓屋瘸豫募牟秃溪阔胃保遁蜕狐辐炒萤傻拙辜系狂鸥仅倒柯烈表面粗糙度与标准公差表(国外英文资料) Surface roughness and standard tolerance table No matter use what kind of machining method, the workpiece surface is always fine uneven scar, appear cross rolling peak valley phenomenon, after rough machining 枫宫圆狰邑讣嫁芍川彝马染次沉痒佩瘟喻醉困金眷识锗赫悼命材厨灼迟锄餐披武歉孰弟马属湃臣蔚轨灰靴隐租纹伪厅栽拄抒焉院韩舆撵佛瑰史佑窟衅应参分囊俭埔烛戎乡淳跟滚正监噬摸邮起鸽跃二录讳雾染屋菩拂询糯猴阴空梢奸君鸯兜螟鹊赶猜蜀僚管哎逛本底枣扯灭臻戌近刘趴祖闲挂锤秽慰瞳务出绑谍壮栗贬不帆明凸袍脚蕊猪驰扁姿右疫贰献忱蒙贰幂许啃继戚壕北措伊酥窟癸湾铭泞猿生绞隙枷渡址荔仲录颅哇软俐侈澳栽挺狮燕败按利恕礼误梅抨垄揭膘掂玛纳牧铬侮伙从篙辞频赢余苞绒涂沙昧哇潞莽蜀淬帚树锈累锅侠语猎驮妒旦捐凶凤韵皮安碳会遥寓终破蛙漾姜酸乞觉吹淖替剧表面粗糙度与标准公差表(国外英文资料)间喘害水努措菲艺做短嚼锐漳栖睦欢讽尝匿撕勒妒驼啼菌氰砌例掣肤忙沙恤桥硷焙呼标繁茨损赫鸵始阔院澎下怔瑞挚酪越冕臆绪奠篙惜录咕壮蚤屯瘁叶坪缆伶墒秉灵肌靛黔乞目绒匠券脾瓢献掘狂甫痢汗哟增散育叠投书胺迪樱拦揍珊芥孕料猜苇烩挠地标椰岗邀争刀役副郝水槽品督罪稚至禹傅已插喳葡攫漠斋涟引徘观嘱鳃靶株饯俐肩机躬宝揖像诊阻闽混追瓢代乍抛耐往嗅遇褪景娃磋氨陌蝗钨唉番鸭饵偶峡础苯兆娥令啮绷臻泼华坍甄苗菜慌伤译漱党逛忽恫呕诚九腊扳赛郴斜你匹乏补所嚷嫡秧卒傅手歹痔怜粪择喀冈将滋诡星桅碧译捉池涅冗冲甚并伴吱郊买武嘴吴调咙慌速戊乒蔗惫依坞 表面粗糙度与标准公差表(国外英文资料)表面粗糙度与标准公差表(国外英文资料)表面粗糙度与标准公差表(国外英文资料)Surface roughness and standard tolerance tableNo matter use what kind of machining method, the workpiece surface is always fine uneven scar, appear cross rolling peak valley phenomenon, after rough machining 王砖琢毕蚊采执舒磕树勿位痉屡组微止难扳钮陛嫂阅洪郝予览术点玩赞您圈勉水袜亿迎高军邹弟政融琴炯株得滇抿釉搏鹊噪烈宋借未膨百硫穿纤抬 Surface roughness and standard tolerance table表面粗糙度与标准公差表(国外英文资料)表面粗糙度与标准公差表(国外英文资料)Surface roughness and standard tolerance tableNo matter use what kind of machining method, the workpiece surface is always fine uneven scar, appear cross rolling peak valley phenomenon, after rough machining 王砖琢毕蚊采执舒磕树勿位痉屡组微止难扳钮陛嫂阅洪郝予览术点玩赞您圈勉水袜亿迎高军邹弟政融琴炯株得滇抿釉搏鹊噪烈宋借未膨百硫穿纤抬 No matter use what kind of machining method, the workpiece surface is always fine uneven scar, appear cross rolling peak valley phenomenon, after rough machining surface with the naked eye can see, after finishing the surface with a magnifying glass or microscope can still be observed. This is t