工厂焊接实习报告精选.docVIP

工厂焊接实习报告精选 1、熟悉焊接方法的种类，熟悉钢材、铸铁、铝及铝合金、铜及铜合金等金属材料的焊接方法。 2、熟悉焊接的有关设备，熟悉焊接材料及选用。 3、初步掌握手工电弧焊、气焊、钎焊等焊接方法。4、初步掌握气焊、手工钎焊工艺、焊接结构工艺设计。 1、看实习图纸。计算角铁45条 2、根据图纸，用切割机将角钢切成所需尺寸。切割时注意： ①角铁标准长度为6m，这时将一条角铁均分为3段，/段;货架焊成后加上角铁厚度刚好长2m，如果下料时2m/段，剩下的第3段就不足2m，造成材料浪费，产品不符要求;10个货架，需/段角铁共80段，一共角铁27条，余2m，可均分为4段为货架宽度所需; ②下料时，将一条角铁均分为3段，/段，剩下1m刚好分2段，/段，为货架宽度所需;10个货架，需/段角铁共40段，一共角铁14条，其中13条余1m，可均分为2段为货架宽度所需;另1条余，可均分为8段为货架宽度所需; ③10个货架，需/段角铁共80段，综合①、②共有8 26 4=38段，还需/段材料42段，即需整条角铁4条，其中3条每条均分为12段，/段，另一条分6段后余3m; ④将/段和/段角铁注意分开摆放，/段用于货架中层，不影响货架尺寸。 3、将/段、/段材料各2段按图纸尺寸，摆为货架支柱，上下层横档;注意对角线长度相等。先电焊，尺寸无误后满焊。 4、按图纸尺寸焊上中层2横档，这样货架一侧就完成了。 5、以第1个支架(货架一侧)为“模板”，完成其它支架。 6、焊货架短横档，注意两侧角度垂直。 　七、实习体会：货架制作应该是最简单的金属焊接——基本只有平焊，当然在不翻动货架的情况下，可以练习立焊、仰焊。制作过程中要注意材料计算，避免浪费。因为电焊弧光含有强烈的紫外线等，对眼睛、皮肤产生灼伤，所以电焊作业千万注意：带面罩、穿较厚的棉工作服、电焊手套、护腿等;做好劳动保护。 daily morning exercises or class-break setting-up exercise and discipline inspection and appraisal of public signs;2, daily cleaning and inspection;3, the daily student school appearance, dress, wearing school card check;4, the daily duty guide to the leadership class discipline three rounds.Weekly moral education work:L, the flag raising ceremony and the national flag speech under the flag raising ceremony held on Monday;2, every week a class meeting, the meeting;3, every week two exercises, cleaning and hygiene, behavior norms, attendance situation published cloth appraisal, and the issue of the code of conduct;;4, weekly work week.Monthly moral education work:1, at least once a month, the theme of education activities, to patriotism education, behavior norms of education as the focus, combined with major retreat day.2, the monthly class quantization assessment and class teacher assessment, selection of behavior for the standard model class.Moral education in each term:1, at the end of each semester to form three good student, outstanding student cadres, civilized student.2, at least once a semester, parents will be.,Student e